Go to Top
SuperLightingLED
SUPERLIGHTINGLED CO., LTD
Web: www.superlightingled.com
Email: [email protected]
Date: 2026-10-23 | ID: 5624

4 Pin Transparent RGB LED Connector - Strip to Wire - For SMD LED Strip

MODEL: RGB-ACCESSORIE-SW
Price based on selections below:
$1.29
Select PCB Width:8mm (0.31in) (Base), 10mm (0.39in) (Base)
AvailabilityIn Stock
ConditionBrand New
Technical Specifications

Create clean, reliable connections for your lighting projects with our 4-Pin Transparent RGB LED Strip-to-Wire Connector. This essential accessory is designed to bridge the gap between your 4-pin RGB LED strips and a power source or controller, eliminating the need for soldering. Its clever clamp design ensures a secure grip on the strip, while the 12cm wire pigtail provides the flexibility needed to connect to controller terminals. Available for both 8mm and 10mm PCB widths, this connector's transparent housing minimizes shadows at the connection point, ensuring a seamless and professional-looking installation. It's the ideal solution for custom lighting setups, navigating corners, or simply connecting your strip light run to its control unit.

Key Features

Solderless Strip Connection

Features an easy-to-use clamp system that creates a secure connection to the LED strip without any soldering.

Dual PCB Width Compatibility

Available in two sizes to perfectly fit either 8mm or 10mm wide 4-pin SMD RGB LED strips.

Pre-Wired for Convenience

Comes with a 12cm (4.72-inch) 4-conductor wire pigtail, ready to be wired into an RGB controller or power source.

Technical Highlights

  • Specifically designed for 4-conductor SMD LED strips.
  • Secure insulation-piercing wire connection and clamp-down strip connection.
  • Suitable for IP20 non-waterproof and IP65 silicone-coated strips.

Product Specifications

Parameter Details
Product Model RGB-ACCESSORIE-SW
Connector Type Strip-to-Wire
Pin Count 4-Pin
Compatible PCB Width 8mm or 10mm (select option)
Total Length Approx. 120mm / 4.72 inches
Housing Material Transparent Plastic
Compatible Strip Types 4-Pin SMD RGB LED Strips
IP Rating Compatibility IP20 (Non-Waterproof), IP65 (Silicone Coated)

Application Scenarios

Connecting LED Strips to Controllers The primary use for this connector is to create a pigtail at the end of a cut section of an RGB LED strip, allowing for easy connection to the terminal block of an RGB controller.
Navigating Obstacles and Corners Use two of these connectors with a length of 4-conductor wire between them to bridge gaps, run wiring around tight corners, or navigate cabinetry and architectural features where the strip itself cannot go.
Custom DIY Lighting Projects Ideal for makers and hobbyists building custom light fixtures. This connector provides a clean and simple way to integrate RGB LED strips into your designs without the hassle of soldering.

How to Use This Connector

  1. Ensure your LED strip is cut cleanly along the designated cut line.
  2. Open the transparent cover of the connector.
  3. Carefully slide the end of the LED strip into the connector, ensuring the copper pads on the strip align with the 4 pins inside the connector. 
  4. Press the transparent cover down firmly until it snaps shut, locking the strip in place. You may use pliers to gently ensure it is fully closed.
  5. Connect the four bare wires to the corresponding terminals on your RGB controller or power supply, ensuring polarity (+, R, G, B) is correctly matched.

4 Pin Transparent RGB LED Connector

⚠ Precautions
  • Always double-check the polarity. Match the positive (+) and R, G, B markings on the strip to the corresponding wires and controller terminals.
  • Ensure you select the correct connector size (8mm or 10mm) to match the PCB width of your LED strip for a secure fit.
  • This connector is not suitable for IP67 or IP68 waterproof strips with a full silicone tube jacket.

What's in the Box

  • ✓1x 4 Pin Transparent RGB LED Connector - Strip to Wire
© 2026 SuperLightingLED. All specifications are subject to change without notice.