Go to Top
SuperLightingLED
SUPERLIGHTINGLED CO., LTD
Web: www.superlightingled.com
Email: [email protected]
Date: 2026-11-18 | ID: 7382

6-Pin SMD Waterproof RGBCCT LED Strip to Strip Jumper Cable Connector 40CM

MODEL: WPACC-SMD-BTBEX-6P12
Price based on selections below:
$4.20
Select PCB Width:12mm (0.47in) (Base)
AvailabilityIn Stock
ConditionBrand New
Technical Specifications

An outdoor-ready jumper connector engineered to bridge two sections of 6-wire 12mm PCB RGBCCT LED strip lights across gaps, corners, or architectural breaks. Measuring 40cm (15.7in) in overall length, this jumper features a durable white-jacketed multi-conductor cable bounded on both ends by solderless quick-connect piercing heads. 

Designed specifically for outdoor RGBWW strip lights, the connector eliminates stripping, scraping, or soldering: hardened copper alloy contact pins pierce through the back of the PCB directly beneath each circuit trace. It fits snugly around IP67 or IP68 strip silicone jackets, preserving exterior weather seals. 

Key Features

Dual Piercing Terminals

Hardened piercing pins penetrate the copper traces from behind the circuit board without stripping the silicone casing.

40cm Flexible Jumper

White insulated 6-conductor wire spans structural gaps, bends around tight 90-degree offsets, and navigates roofline obstructions.

Dedicated 12mm SMD Fit

Molded alignment guides position 12mm wide 6-wire SMD PCB tape with total outer jacket widths up to 14mm.

Integrated Sealant Port

A top-access aperture permits direct injection of silicone glue to restore IP67 and IP68 waterproof ratings.

6A Current Handling

Rated for up to 6A continuous throughput, accommodating multi-meter DC 12V and DC 24V tunable color runs.

Waterproof LED to LED Connector

Product Specifications

ParameterDetails
ModelWPACC-SMD-BTBEX-6P12
Housing MaterialFlame-Retardant Polycarbonate (White)
Connector TypeStrip to Strip Extension Connector
PCB Width12mm (0.47in)
Compatible Outer Strip Width14mm (with silicone casing)
Conductor Count6 Pins (V+, R, G, B, W/CW, WW)
Total Cable Length40cm (15.75in)
Rated Current6A Maximum Total (1A to 1.5A per channel)

Application Scenarios

Patio and Deck Perimeter Lighting Bridge exterior 12mm 6-conductor tape light around stair stringers, support posts, and patio railing transitions. The 40cm jumper routes around framing lumber without pinching delicate circuit traces.
Outdoor Kitchen and Bar Counters Navigate tight under-counter angles and split island cabinetry runs. The puncture contacts pierce through IP67 silicone layers to maintain continuous dynamic color and tunable white illumination.
Architectural Soffits and Rooflines Connect separated roof eave lighting runs while protecting electrical joints against rain runoff and moisture ingress. Adding silicone glue through the injection port ensures an IP68 moisture seal.

How to Install & Connect This 6-Pin Waterproof LED Strip Jumper

  1. Cut your waterproof RGBCCT LED strip along the designated copper cut line using a sharp utility knife or shears. Ensure a clean 90-degree cut without jagged silicone edges.
  2. Insert the cut LED strip end into the transparent alignment frame.
  3. Position the LED strip contact pads over the sharp metal piercing pins with the puncture hole side facing downward. Verify that the polarity markings.
  4. Use parallel-jaw pliers or firm thumb pressure to squeeze the clear housing shut until the internal pins pierce completely through the PCB board.
  5. Connect the circuit to your RGB+CCT controller to verify color switching and tunable white operation across both strip segments.
  6. Inject non-corrosive silicone sealant (electronic grade RTV) through the top glue hole and seal both wire entrance seams to ensure complete IP68 waterproof integrity. 

⚠ Precautions

  • SMD strips only: This connector is designed for 12mm-PCB SMD circuit boards and is incompatible with continuous COB LED strips.
  • Do not peel off the top silicone cover; the piercing teeth are engineered to press through the PCB from underneath.
  • Never cross polarities; ensure the DC positive line (+24V or +12V) matches across both ends before locking the clamps.

What's in the Box

  • ✓1x 6-Pin 12mm Waterproof RGBCCT LED Strip to Strip Jumper Cable (40cm overall length)

 

© 2026 SuperLightingLED. All specifications are subject to change without notice.