Go to Top
SuperLightingLED
SUPERLIGHTINGLED CO., LTD
Web: www.superlightingled.com
Email: [email protected]
Date: 2026-11-18 | ID: 7384

6-Pin COB 12mm RGB CCT LED Strip Pigtail Connector Cable 11CM

MODEL: RGBCCT-COB-6P-BTW
Price based on selections below:
$1.49
AvailabilityIn Stock
ConditionBrand New
Technical Specifications

The RGBCCT-COB-6P-BTW establishes a solderless terminal connection between 12mm wide 6-pin RGBCCT COB LED strips and your system driver or lighting controller. Measuring 11.3cm in overall length with a 10cm 22AWG 6-conductor wire pigtail, this cob strip light connector eliminates manual soldering while securing reliable electrical contact across six channels (+, R, G, B, CW, WW). 

Designed specifically for IP20 non-waterproof bare board COB LED strip lights, the transparent housing features six internal metal piercing prongs that bite directly into the copper solder pads under hand-plier pressure. The six free-end flying leads feed straight into screw terminals on a dimmer, receiver, or driver, giving installers complete freedom over wire routing and polarity assignment during field installations.

If you don't need a fixed cable length, please check out the board-to-cable connectors.

Key Features

Insulation-Piercing Contact Teeth

Six sharp copper-alloy blades puncture through the LED strip circuit board to grip contact pads directly without stripping or soldering.

Dedicated 12mm RGBCCT Layout

Form-fitted 12mm internal channel supports 6-pin continuous-phosphor COB LED strip lights without pinching phosphor edges.

Factory-Attached 22AWG Pigtail

Supplied with 10cm (approx. 4 inches) of flexible 22AWG stranded wire leads for direct insertion into receiver screw clamps.

Product Specifications

ParameterDetails
Product ModelRGBCCT-COB-6P-BTW
Connector Type1*Strip to Wire Connector With Cable
Pin Count6-Pin
Compatible Strip TypeRGBCCT COB LED Strip Lights
Compatible PCB Width12mm (0.47 in)
Compatible Ingress RatingIP20 (Non-Waterproof Bare Board)
Connection MechanismSolderless Insulation Piercing
Overall Assembly Length11.3cm (4.45 in)
Lead Wire Length10cm (approx. 4 inches)
Wire Gauge22AWG Stranded Copper
Conductor Count6-Conductor Pigtail

[ VIDEO: Watch on YouTube ]

Closed solderless 6-pin COB LED strip connector with attached 22AWG pigtail wire

[ VIDEO: Watch on YouTube ]

12mm COB LED strip connector dimensions: 13.76mm length by 12.16mm width

Application Scenarios

Cabinet & Millwork Power Infeeds Feed power and control signals from remote drivers into cut-to-length 12mm RGBCCT COB tape runs hidden beneath kitchen shelving. The 10cm pigtail wire routes cleanly through drilled shelf partitions directly into low-voltage lighting cable connectors without bulky inline junction boxes.
Architectural Aluminum Extrusions Connect discrete tape sections inside standard 15mm-wide recessed or surface LED aluminum channels. Because the housing is only 4mm high, it closes beneath frosted diffuser covers without casting visible dark spots across tunable white or saturated color scenes.
On-Site Field Retrofits and Maintenance Replace damaged infeed lines or extend freshly cut reel remnants without hauling soldering guns, flux, or heat-shrink tubing onto job site ladders. Technicians can complete secure board-to-wire connections in tight ceiling coves using standard parallel slip-joint pliers.

How to Connect 12mm RGBCCT COB LED Strip Lights

  1. Cut your 12mm RGBCCT COB LED strip strictly along the marked cut line using sharp shears, ensuring the six copper contact pads remain intact and clean.
  2. Slide the cut end of the 12mm COB LED strip into the connector guide slots until the six copper pads sit squarely over the internal metal piercing pins.
  3. Use parallel pliers to press the pins firmly down. This action presses the metal piercing prongs through the strip PCB pads.
  4. Verify each conductor color on the 10cm pigtail against your strip pads (+, R, G, B, CW, WW) before terminating the stripped wire ends into your RGB+CCT controller.
  5. Perform a gentle pull test on the LED strip and wire leads to ensure firm mechanical retention, then reapply low-voltage power to test all 5 color channels.

⚠ Precautions

  • This accessory is engineered strictly for 12mm wide IP20 non-waterproof bare board RGBCCT COB LED strip lights; it is not compatible with 10mm tape, waterproof silicone sleeves, or standard SMD strips with tall diodes.
  • Always use flat-jaw pliers to apply even pressure across the entire width of the cap; uneven finger pressure may fail to drive the contact prongs through the copper layer.
  • Verify contact polarity before clamping the connector shut. Reversing positive and negative paths can short your LED strip, RGBCCT controller, or 12V/24V power supply.

What's in the Box

  • ✓1x 6-Pin 12mm COB LED Strip to Wire Pigtail Connector with 10cm 22AWG Cable

 

© 2026 SuperLightingLED. All specifications are subject to change without notice.