Go to Top
SuperLightingLED
SUPERLIGHTINGLED CO., LTD
Web: www.superlightingled.com
Email: [email protected]
Date: 2026-11-18 | ID: 7386

DC12V UCS2904B Addressable RGBW Multi-Color Flexible 5050 SMD LED Strip 60-LEDs/m

MODEL: UCS2904B-RGBW-60W10-12V
Price based on selections below:
$49.98
Select IC Pixels:20 Pixels/Meter (60 LEDs/Meter) (Base)
Select Length:16.4ft (5 meters) (Base)
Select Light Color :RGB + Daylight White 6000K (Base), RGB + Warm White 3000K (Base), RGB+ Natural white 4000K (Base)
Select PCB Color :White Background (Base), Black Background (Base)
Select PCB Width:10mm (0.39in) (Base)
Select Waterproof Rating:Non-Waterproof IP20 - Adhesive Back (Base), Surface Glued IP65 - Adhesive Back, Outdoor Silicone Tube IP67 - With Brackets, Underwater IP68 - Adhesive Back, Outdoor Silicone Tube IP67 - Adhesive Back, Underwater IP68 - With Brackets
AvailabilityIn Stock
ConditionBrand New
Technical Specifications

The DC12V UCS2904B addressable RGBW 5050 SMD LED strip light delivers independent color chasing, scene programming, and true architectural white illumination across a 16.4ft (5-meter) reel. Operating at DC 12V, this digital led smd 5050 strip integrates external UCS2904B constant-current driver ICs, configuring every 3 LEDs as one independently controllable pixel (20 pixels per meter, 100 pixels per reel). 

Each SMD 5050 package integrates four semiconductor dies—red, green, blue, and a dedicated white emitter (selectable in 3000K warm white, 4000K natural white, or 6000K daylight white)—eliminating the uneven bluish casts common to standard RGB-only mixing. Built on a 10mm wide flexible printed circuit board (FPC) with 18W per meter power consumption, this smd led strip light includes pre-soldered 3-pin signal and 2-pin power-injection JST-SM connectors on both ends for clean installation and robust data continuity.

Key Performance Features

External UCS2904B IC Control

Each external UCS2904B driver IC controls 3 SMD 5050 RGBW LEDs with 17mA constant-current accuracy within +/-1.5% between channels, providing 256 grayscale levels per channel and an 800 kbps transmission rate.

4-in-1 SMD 5050 RGBW Architecture

Houses dedicated red, green, blue, and pure white diodes within a single 5.0mm x 5.0mm package, delivering true functional white illumination alongside saturated dynamic chasing effects.

50mm Segment Trimming

Features designated cut marks spaced every 3 LEDs (50mm / 1.97 in), allowing field customization and solder-pad splicing to match precise architectural alcoves and cabinet runs.

Dual JST-SM Connector Design

Equipped with factory-installed 3-pin data connectors and auxiliary 2-pin power injection leads on both reel ends, simplifying bilateral power injection to prevent end-of-run voltage drop.

Four Environmental Protection Ratings

Available in non-waterproof IP20 (2.1mm profile height), surface glued IP65, outdoor silicone sleeved IP67, and fully submersible IP68 configurations with mounting brackets or adhesive backing.

Product Specifications

ParameterDetails
Product ModelUCS2904B-RGBW-60W10-12V
Input VoltageDC 12V
Power Consumption18W/m (90W per 5m roll)
IC TypeExternal UCS2904B (SOP8)
LED TypeSMD 5050 4-in-1 RGBW
LED Density60 LEDs/m (300 LEDs per 5m roll)
Pixel Resolution20 pixels/m (100 pixels per 5m roll; 3 LEDs/pixel)
Cut IntervalEvery 50mm (2.0 in) / 3 LEDs
White Color Options3000K Warm White / 4000K Natural White / 6000K Daylight White
Grayscale Level256 levels (8-bit per channel, 32-bit color depth)
PWM Scan Frequency1.8 kHz
Data ProtocolSingle-line Return-to-Zero (NZR) 800 kbps
PCB Width10mm (0.39 in)
Profile Height2.1mm (IP20 bare board)
PCB ColorWhite
Reel Length16.4ft (5.0 meters)
Terminal Connectors3-pin JST-SM (V+, Data, GND) + 2-pin JST-SM (V+, GND)
Waterproof OptionsIP20, IP65, IP67, IP68
Manufacturer Warranty2 Years

Application Scenarios

Commercial Hospitality & Accent Lighting Installed inside perimeter ceiling coves, restaurant bar fascias, and hotel lobby bulkheads. The dedicated 3000K or 4000K white channel supplies practical ambient lighting during operational hours, while the RGB pixels switch to dynamic scene chasing for evening events.
Stage Productions & Live Entertainment Venues Utilized across concert stages, broadcast backdrops, and nightclub truss installations. The 1.8 kHz PWM refresh frequency prevents camera shutter banding, and the UCS2904B protocol integrates seamlessly into Art-Net and DMX-to-SPI pixel-mapping software.
Architectural Facades & Exterior Outlines Mounted with IP67 silicone sleeves or IP68 solid encapsulation along building cornices, roof perimeters, and patio contours. Resists rain, humidity, and temperature variations from -40 deg C to +85 deg C while providing vivid color changes.

How to Install & Use This LED Strip

  1. Check that the incoming DC power supply matches DC 12V. Disconnect all AC mains power before making any wire terminations.
  2. Trim the LED strip only along the marked copper cut lines spaced every 50mm (3 LEDs). Never cut across active IC circuits or internal traces.
  3. Connect the 3-pin input JST-SM plug to your SPI pixel controller: Red wire to DC12V (V+), Green wire to Data (DAT), and White wire to Ground (GND). Ensure the data direction matches the printed directional arrows on the PCB.
  4. Connect both the front and rear 2-pin power wires to your 12V DC power bus. Dual-end power injection is strongly advised on 5-meter runs to maintain consistent color balance when all RGBW channels operate simultaneously.
  5. Configure your controller software (such as WLED, Madrix, or standard SPI hardware) to the UCS2904 or UCS2904B IC profile, selecting the RGBW color order that matches your unit.
⚠ Precautions
  • Never connect this DC 12V LED strip directly to AC 110V/220V mains or DC 24V power sources, as overvoltage will instantly damage the UCS2904B ICs and LED chips.
  • Single-end power injection across a full 5-meter reel will cause slight voltage drop at the far end when displaying full-white or mixed multi-color scenes; always inject DC 12V power at both ends for uniform brightness.
  • Select an appropriate power supply rated for at least 110W per 5-meter reel (18W/m x 5m = 90W, plus a 20% operating headroom buffer).

What's in the Box

  • ✓1 x 16.4ft (5m) Reel of DC12V UCS2904B RGBW 60 LEDs/m LED Strip Light
  • ✓Pre-soldered 3-Pin JST-SM Signal Connector and 2-Pin Power Injection Leads on Both Ends

⇩ Downloads & Documents

PDFUCS2904-Datasheet

Frequently Asked Questions

Q: What type of controller do I need for this LED strip?

A:You need a dedicated addressable LED controller that is specifically compatible with the UCS2904 or UCS2904B RGBW single-line data protocol, capable of sending 800 kbps non-return-to-zero SPI signals across four color channels.

Q: Can I connect multiple 5-meter rolls together?

A:Yes, you can connect the data line from one roll to the next. However, you must inject power from a separate LED power supply for each 5-meter roll to avoid brightness and color issues caused by voltage drop.

Q: Why is dual-end power feeding recommended for this 12V strip?

A:At 18W per meter, a full 5-meter reel consumes 90W under full load. Feeding DC 12V power only from one end causes minor resistance-based voltage drops at the tail end during mixed-color operation; injecting power at both ends ensures uniform illumination and color consistency.

 

© 2026 SuperLightingLED. All specifications are subject to change without notice.