Spec Sheet - FSLCOB-1224VRGB-576W10

Select Connector:	4-Pin Plug Connectors (Base)
Select Input Voltage:	DC24V (Base), DC12V (Base)
Select Length:	16.4ft (5 meters) (Base)
Select PCB Width:	10mm (0.39in) (Base)
Select Waterproof Rating:	Non-Waterproof IP20 - Adhesive Back (Base), Underwater IP68 - Adhesive Back, Outdoor Silicone Tube IP67 - Adhesive Back
Availability	In Stock
Condition	Brand New

The FSLCOB-1224VRGB-576W10 series RGB COB LED strip light delivers continuous, dot-free color mixing across 576 micro-LED chips per meter. Engineered for residential ambient accents and architectural integration, this 10mm flexible LED strip operates at 14W per meter and is available in both 12V and 24V DC configurations. Each 5-meter reel comes pre-wired with 4-pin male and female plug-in pin connectors on opposite ends for immediate connection to RGB 4-channel controllers. This LED strip incorporates a standard 4-pad surface layout, positioning two solder pads on each side of the linear coating to support 10mm 4-pin solderless COB connectors.

Key Features

Dual Voltage Engineering

Select between 12V DC (3.0mm profile) for vehicle and battery installations, or 24V DC (2.2mm profile) for 5-meter single-feed runs with zero visible voltage drop.

Precise 31.25mm Cut Increments

Copper cut marks every 31.25mm allow exact field sizing inside tight cabinetry, aluminum profiles, and decorative perimeter coves.

Pre-Installed Dual End Terminations

Supplied on a 5-meter reel with pre-attached 4-conductor input and output pins on opposite ends to accelerate system mock-up and wiring.

Technical Highlights

14W/m power consumption totaling 70W per full 5-meter reel, requiring 84W minimum power supply sizing with a 20% safety margin.
24V model maintains uniform luminous intensity across the entire 5m run with single-ended power injection.
12V model exhibits measurable voltage attenuation on the final 1.0 meter when R, G, and B channels run simultaneously at 100% duty cycle on single-ended feeds; double-ended feeding solves this limitation, as detailed in our low-voltage project guide.
Pair the 12V edition directly with regulated 12V desktop power supplies for localized under-shelf installations.
Drive the 24V edition using matching 24V desktop power supplies to ensure stable color consistency across extended lengths.
Mount into surface mount corner channels to enhance passive thermal dissipation and safeguard the PCB against physical contact.

Product Specifications

Parameter	Details
Product SKU	FSLCOB-1224VRGB-576W10
Operating Voltage	DC 12V or DC 24V (Selectable)
LED Technology	COB (Chip-on-Board)
LED Density	576 LEDs per meter
Power Consumption	14W/m (70W per 5m reel)
Color Configuration	RGB (Red, Green, Blue)
Beam Angle	180°
PCB Width	10mm (0.39 in)
Strip Height / Thickness	12V: 3.0mm; 24V: 2.2mm
Reel Length	5 meters (16.4 feet)
Cut Interval	31.25mm (1.23 in)
Connection Interface	4-pin plug-in headers pre-installed on both ends
Solderless Connector Compatibility	10mm 4-pin COB solderless connectors
Ingress Protection	IP20, IP67, IP68
Operating Temperature	-20°C to +45°C
Dimming & Control Mode	Common Anode (V+ / R- / G- / B-) PWM Dimmable

Application Scenarios

Under-Cabinet Accent IlluminationEliminate glossy stone countertop reflections with dot-free COB diffusion. Mount this 10mm RGB COB LED strip under kitchen cabinetry to wash backsplashes in saturated accent tones without visible diode dots.

Gaming Desk and Media Center BacklightingApply the flexible LED strip along desk perimeters and monitor displays for immersive bias lighting. The 31.25mm cut intervals allow precise sizing around display mounts and computer workstations.

Retail Display and Shelving DisplaysFit the narrow 10mm profile directly into display showcases and product shelving. The wide 180° beam angle bathes merchandise evenly without harsh glare or distracting point-source reflections.

How to Install & Use This LED Strip

Measure the required installation length and cut the LED strip strictly along the designated copper cut lines spaced every 31.25mm using clean shears.
Connect the 4-pin leads (V+, R, G, B) to your RGB controller, matching polarity markings accurately.
Power the assembly temporarily to confirm full red, green, and blue channel output across all segments.

⚠ Precautions

The 12V edition shows voltage drop across the final 1.0m when all channels operate at 100%; feed both ends with DC power to maintain uniform color.
Always calculate power supply capacity with a 20% headroom factor: size at least 84W of power supply capacity for a single 5m reel operating at 70W.

What's in the Box

✓1 × 5m (16.4ft) Reel of FSLCOB-1224VRGB-576W10 RGB COB LED Strip Light
✓2 × Pre-soldered 4-Pin Plug-in Connectors (one male, one female at opposite ends)

Frequently Asked Questions

Q: how to connect cob led strip

A: You can connect this LED strip using its pre-attached 4-pin plug-in headers, soldering wires directly onto the solder pads, or inserting cut ends into standard 10mm 4-pin COB solderless clamp connectors.

Q: how to cut rgb led strip lights

A: Cut directly across the black dashed line centered between the dual copper pads every 31.25mm using sharp electronics scissors while the power supply is disconnected.

Q: What is the difference between the 12V and 24V versions?

A: The 12V version measures 3.0mm high and exhibits voltage drop on the final 1 meter of a 5m single-ended feed when white light (all channels) is displayed, whereas the 24V version is 2.2mm high and operates 5 meters continuously with zero visible voltage drop.

Low Voltage DC 12V 24V RGB Cob Strip Light Cuttable Connectable 576 LEDs