Go to Top
SuperLightingLED
SUPERLIGHTINGLED CO., LTD
Web: www.superlightingled.com
Email: [email protected]
Date: 2026-10-29 | ID: 7356

DC24V SM16703P Pixel Control 2-in-1 3527 Dual White 10mm LED Strip

MODEL: FSLCCT-SM16703P-120W10
Price based on selections below:
$40.98
Select IC Pixels:20 Pixels/Meter (120 LEDs/Meter) (Base)
Select Length:16.4ft (5 meters) (Base)
Select Light Color :Warm White(2700K) + Daylight White(6500K) (Base)
Select Waterproof Rating:Non-Waterproof IP20 - Adhesive Back (Base), Surface Glued IP65 - Adhesive Back, Underwater IP68 - Adhesive Back, Outdoor Silicone Tube IP67 - Adhesive Back
AvailabilityIn Stock
ConditionBrand New
Technical Specifications

This DC24V addressable white LED strip light integrates dual-color 2-in-1 SMD3527 emitters with external SM16703P driver ICs, delivering smooth color temperature tuning from 2700K warm white to 6500K cool white alongside dynamic chasing effects. Operating at 18.7W per meter with a density of 120 LEDs per meter, each external IC manages a 6-LED segment (20 addressable segments per meter) across a 10mm wide PCB. Sold as a complete 5-meter (16.4-foot) continuous reel with pre-attached 3-pin JST SM connectors at both ends, this LED strip provides up to 22 lumens per diode with a color rendering index of CRI ≥90. 

Key Features

SM16703P Pixel Architecture

Each external SM16703P IC addresses a 6-LED segment, generating 20 controllable zones per meter for smooth flowing, theater-chasing, and dimming animations.

Dual-Color 2-in-1 SMD3527

Houses warm white (2700K) and cool white (6500K) dies inside a single package for unified color mixing without visible color separation.

High Color Fidelity CRI ≥90

Provides accurate tonal reproduction across architectural surfaces, millwork, and display cases without dulling neutral shades.

DC 24V Constant Voltage Drive

Reduces operating current and prevents visible voltage drop across the 5-meter run compared to standard 5V or 12V digital LED strips.

Dual-Ended 3-Pin JST Connections

Features pre-soldered 3-wire JST SM connectors on both ends for direct data transmission and convenient power reinjection.

Technical Highlights

  • Configured with 20 addressable pixels per meter (1 pixel per 6 LEDs / 50mm cut increment).
  • Functions on standard 3-wire single-line SPI data protocols (V+, Data, GND).
  • Engineered on a 10mm wide, flexible copper circuit board with self-adhesive backing for heat sinking into aluminum extrusions.

Product Specifications

ParameterDetails
Product Model (SKU)FSLCCT-SM16703P-120W10
LED Chip BrandSanan
Operating VoltageDC 24V
Power Consumption18.7W/m (93.5W per 5m roll)
IC TypeExternal SM16703P
LED TypeSMD 3527 2-in-1 Dual-Color
Color Rendering Index (CRI)≥90 Ra
LED Density120 LEDs/m (600 LEDs per 5m reel)
PCB Width10mm
Pixel Resolution20 pixels/m (1 IC per 6 LEDs)
Color Temperature2700K - 6500K CCT Tunable White
Beam Angle120°
DimmableYes (via compatible digital SPI controller)
Ingress ProtectionIP20, IP65, IP67, IP68
Warranty2 Years
Standard Roll Length5 meters (16.4 feet)
Connector Type3-pin JST SM connector on both ends
Supplier-Rated Lifespan50,000 operating hours

Application Scenarios

Linear Architectural Coves and Recessed Ceilings Install this addressable warm white LED strip inside ceiling coves to run subtle gradient washes, sunrise color transitions, and sequential lighting scenes across large interior spans.
Under-Cabinet and Joinery Task Lighting Utilize 2700K-6500K tunable white LED light strips along kitchen millwork and office cabinetry, adjusting between focused 5000K daylight for tasks and 2700K ambient illumination in the evening.
Staircase and Hallway Motion Chasing Program the 20 segments per meter to activate sequentially in response to motion sensors, providing an illuminated pathway along stair treads and corridor baseboards.
Exhibition Displays and Retail Showcases Leverage CRI ≥90 color reproduction and smooth chasing modes inside retail shelving and vitrines to accentuate luxury merchandise without color distortion.

How to Install & Use This LED Strip

  1. Connect the 3-pin JST connector to your 24V SPI tunable white controller: Red wire to DC24V (+), Green wire to Data (DAT), and White wire to Ground (GND).
  2. Power on the DC 24V driver and test all static CCT mixes and digital chasing patterns before removing the adhesive backing.
  3. If cutting is necessary, cut only along the marked solder pads situated every 6 LEDs (approx. every 50mm).

⚠ Precautions

  • Ensure your DC 24V power supply provides at least 113W of capacity per 5m reel to account for the standard 20% safety headroom (93.5W load × 1.2).
  • Connect power injection cables directly to both ends if linking multiple reels end-to-end to avoid thermal buildup and voltage drop.

What's in the Box

  • ✓1 × 5-Meter (16.4ft) Reel of DC24V Addressable 3527 CCT LED Strip Light
  • ✓2 × Pre-attached 3-Pin JST SM Connectors (1 input, 1 output)
© 2026 SuperLightingLED. All specifications are subject to change without notice.