Go to Top
SuperLightingLED
SUPERLIGHTINGLED CO., LTD
Web: www.superlightingled.com
Email: [email protected]
Date: 2026-11-16 | ID: 7383

2-Conductor Waterproof LED Strip Corner Connector

MODEL: WPACC-SC-2P-L
Price based on selections below:
$1.99
Select PCB Width:8mm (0.31in) (Base), 10mm (0.39in) (Base)
AvailabilityIn Stock
ConditionBrand New
Technical Specifications

This 2-pin L-shaped waterproof LED strip corner connector creates clean 90-degree turns for moisture-exposed installations without cutting traces or soldering wire jumpers. Built with a two-part piercing mechanism, the assembly pairs a rigid white terminal base with dual transparent locking brackets that position each LED strip firmly over solid copper contact pins. The downward-piercing design penetrates the underside of the flexible circuit board directly, establishing a reliable electrical bond with low-voltage LED systems while preserving continuous silicone jacket protection.

Available in dedicated 8mm and 10mm board widths, this corner connector accommodates single-color SMD tape along with dot-free white COB LED strip and colored COB LED strip options. Whether outfitting outdoor soffits, commercial kitchen counters, or shower niches, this fitting maintains continuous DC polarity around tight structural corners.

Key Features

Solderless Piercing Contact

Hardened copper alloy pins pierce directly through the underside of the LED strip PCB to make a vibration-resistant electrical bond without stripping silicone.

True 90-Degree L-Configuration

Pre-molded right-angle layout eliminates strip folding and stress cracking on interior corner joints.

Dual PCB Width Options

Available in 8mm and 10mm PCB width options to prevent lateral strip misalignment across single-color LED strip lights.

Transparent Locking Sleeves

Clear retention carriers allow direct visual verification of conductor alignment and pin seat depth before locking.

SMD and COB Compatibility

Engineered clearances seat traditional SMD chips as well as continuous phosphor-layer COB LED strip geometries.

6A Current Capacity

Supports up to 6A of continuous load, handling 72W runs at 12V DC and 144W runs at 24V DC.

Product Specifications

ParameterDetails
Model SKUWPACC-SC-2P-L
Connector TypeL-shaped strip-to-strip corner connector
Contact Pin Count2 Pins (+ / -)
Overall Dimensions (L x W x H)23.8mm x 23.8mm x 9mm
Compatible PCB Widths8mm or 10mm (selectable)
Compatible Strip ArchitectureSMD and COB single-color
Compatible Ingress ProtectionIP67 (silicone coated), IP68 (silicone tube)
Maximum Current Rating6A continuous
Carrier FrameHigh-transparency polycarbonate
Base Body MaterialFlame-retardant polycarbonate
Contact Pin MaterialTinned phosphor bronze

Application Scenarios

Under-Cabinet Kitchen ReturnsRoute continuous task lighting around 90-degree kitchen cabinetry corners without dead zones. The compact profile tucks into standard light valances while withstanding steam and moisture.
Architectural Outdoor Soffits and EavesTurn exterior fascia corners on residential rooflines. When combined with outdoor silicone sealant, the housing maintains electrical continuity without corrosion across seasonal humidity swings.
Bathroom Coves and Shower NichesNavigate perimeter tile angles in wet areas. For tips on choosing fittings for high-humidity areas, read our guide to selecting connectors.

How to Install the 2-Pin Waterproof LED Strip Corner Connector

  1. Trim your waterproof LED strip to the required cut line using sharp shears, ensuring an even, perpendicular cut across both copper contact pads.
  2. Take one transparent bracket carriage and slide the cut end of the waterproof LED strip into the channel with the aperture window facing downward toward the contact pads.
  3. Verify that the LED strip copper solder pads are fully centered within the transparent frame's bottom opening window.
  4. Seat the loaded carriage onto the corresponding arm of the white 90-degree pin base, matching polarity markings (+ and -) between both LED strip segments.
  5. Using parallel-jaw pliers or firm thumb pressure, press the transparent carriage down into the base until the bottom pins pierce the PCB board and the side latches click shut.
  6. Repeat the insertion and compression process for the second LED strip section on the adjacent 90-degree arm.
  7. Apply power to verify illumination. For exterior or wet-location use, inject neutral-cure silicone sealant into both cable entry openings.
⚠ Precautions
  • Always confirm your LED strip board width (8mm vs 10mm) prior to purchase; placing an 8mm board into a 10mm housing will cause off-center pin contact.
  • Observe polarity: ensure the positive trace line (+/V+) on the incoming LED strip routes to the positive trace line on the outgoing LED strip.
  • Never exceed the 6A maximum continuous load rating of this connector terminal.

What's in the Box

  • ✓1 x 2-Pin L-Shaped White Terminal Base
  • ✓2 x Transparent Retaining Bracket Sleeves

Frequently Asked Questions

Q: Will this corner connector fit both 8mm and 10mm LED strips?

A: The connector is manufactured in two dedicated width sizes: 8mm and 10mm. You must measure your LED strip's bare circuit board width and select the corresponding size from the product options.

Q: Is soldering required to join two waterproof LED strip lights at a 90-degree angle?

A: No soldering is required. The integrated piercing pins make solid electrical contact through the circuit board when pressed into place.

Q: Can I use this connector with continuous COB LED strip lights?

A: Yes, this connector is fully compatible with 2-pin single-color COB LED strip lights as long as the strip board width matches your selected connector width (8mm or 10mm).

 

© 2026 SuperLightingLED. All specifications are subject to change without notice.