Go to Top
SuperLightingLED
SUPERLIGHTINGLED CO., LTD
Web: www.superlightingled.com
Email: [email protected]
Date: 2026-10-19 | ID: 7323

12V COB Individual Pixel LED 5mm RGB 800 Lights Addressable Strip

MODEL: FSLCOB-12V-WS2812BX160
Price based on selections below:
$45.98
Select COB Type:12V Slim 5mm 160/m (Base)
Select Connector Type:JST Fast Connectors (Base), Waterproof Wires
Select Length:16.4ft (5 meters) (Base)
Select Waterproof Rating:Non-Waterproof IP20 - Adhesive Back (Base), Transparent Heat Shrink Tube IP67
AvailabilityIn Stock
ConditionBrand New
Technical Specifications

The FSLCOB-12V-WS2812BX160 delivers true dotless linear illumination in an ultra-narrow 5mm PCB form factor. Operating on DC 12V power, this addressable cob rgb led strip packs 160 individual WS2812B ICs and 160 LED emitters per meter (800 pixels across each 16.4ft / 5-meter reel). Each diode acts as an independent pixel, giving designers complete single-pixel control for chasing, gradient pulsing, and pixel-mapped graphics without the hot spots of traditional SMD tape. 

Engineered 12V circuit maintains uniform color and lumen output across the full 5m run. Pair this strip with any standard SPI LED controller to orchestrate 16.7 million dynamic colors across vehicles, boats, tight architectural millwork, or micro aluminum profiles. For wet locations or marine installations, select the IP67 heat-shrink option. 

Key Features

1-to-1 Individual Pixel Control

Features 160 WS2812B IC chips per meter paired with 160 LED chips, fully compatible with open-source controllers running WLED, FastLED, NeoPixel libraries, Arduino, and DMX-SPI signal decoders.

Ultra-Narrow 5mm PCB Profile

The 5mm slim width fits directly into tight architectural reveals, vehicle interiors, marine consoles, and small silicone neon tubing.

Stable 12V Power Delivery

Engineered 12V DC input runs up to 5 meters without visible voltage drop or end-to-end color deviation, consuming 10W per meter. Input termination default with a 3-pin JST-SM female plug, paired with a dual-conductor power tail on the output end.

Versatile Connector & Ingress Choices

Available in non-waterproof IP20 with 3M thermal adhesive back or factory-sealed IP67 transparent heat shrink sleeve with waterproof wires or JST fast connectors.

Product Specifications

ParameterDetails
ModelFSLCOB-12V-WS2812BX160
LED TypeChip-on-board
Operating VoltageDC 12V
Power Consumption10W/m (50W per 5m reel)
PCB Width5mm (0.20 in)
Strip Height2.5mm (0.10 in)
Reel Length5 meters (16.4 ft)
LED Density160 LEDs/m (800 LEDs/reel)
Pixel Density160 Pixels/m (800 Pixels/reel)
IC TypeWS2812B (Single Data Line)
Emitting ColorDigital RGB
Cut Unit12.5mm (4.9in)
LED Spacing6.25mm (0.246in), two LEDs per cut
Beam Angle180°
Ingress ProtectionIP20 (Adhesive Back) or IP67 (Heat Shrink Tube)
Input Interface3-Pin JST-SM Connector (+12V, Data, GND)
Output Interface2-Conductor DC Power Injection Tail

Application Scenarios

Vehicle and Marine Accent Illumination Operating natively on DC 12V electrical systems, this addressable led strip rgb seamlessly integrates into RV cabins, automobile dashboards, yacht cockpits, and boat interiors without requiring DC step-down converters. The slim 5mm profile tucks neatly into narrow interior seams and under-deck recesses.
Ultra-Compact Architectural Slots & Millwork Designed for tight cabinetry grooves, narrow floating shelves, and slim display cases where standard 10mm tape light cannot fit. The continuous cob leds strip emitter guarantees uninterrupted linear diffusion without scalloping, even when recessed into shallow 5mm aluminum channels.
Custom Neon Flex Fabrication & Stage Elements Because the 5mm flex board slides smoothly into 5mm silicone neon diffuser sleeves, it serves as the dynamic light engine for custom signage, wearable props, and live-event pixel fixtures that require 160 pixels/m fluid chasing patterns.

How to Install & Use This LED Strip

  1. Cut only along designated copper solder pad cut marks if length adjustment is needed. Reseal any cut edges with silicone sealant and end caps on IP67 versions.
  2. Connect the 3-pin JST-SM input plug to your digital SPI controller, verifying that +12V, Data In (DI), and Ground (GND) match the controller terminals. The power cords on the output side must not come into contact with each other, as this could cause a short circuit.
  3. Apply DC 12V power from an LED driver sized for at least 60W per 5-meter run to allow a 20% operating safety margin.
  4. When installing multiple 5-meter reels, wire all DC12V power inputs in parallel back to the power supply to prevent voltage drop and maintain balanced pixel brightness across long distances.
3-Pin Addressable LED Strip Wiring Diagram

⚠ Precautions

  • For continuous runs exceeding 5 meters, inject 12V DC power at every 5m juncture using the attached 2-conductor power leads.

What's in the Box

  • ✓1 × 16.4ft (5m) Reel 12V COB 5mm WS2812B Addressable LED Strip Light
  • ✓1 × Pre-attached 3-Pin JST-SM Connector Set
  • ✓1 × Factory-Soldered 2-Wire DC Power Injection Tail

Frequently Asked Questions

Q: Does this 12V 5m strip suffer from voltage drop like 5V strips?

A:No. Operating at 12V draws lower amperage than 5V strips, allowing the full 5-meter (16.4ft) reel to run without visible color shifting or brightness dimming along the length.

 

© 2026 SuperLightingLED. All specifications are subject to change without notice.