Spec Sheet - SR-ZG9101EA-5C

Availability	In Stock
Condition	Brand New

The Sunricher SR-ZG9101EA-5C is a constant voltage 5-channel Zigbee 3.0 controller engineered for precise management of low-voltage LED lighting systems. Operating across a wide DC 12-48V range, this multi-mode receiving unit features onboard DIP switches allowing users to switch freely between RGB+CCT, RGBW, tunable white, and single color output modes.

Whether paired alongside a dedicated NFC Zigbee LED driver or wired to centralized constant voltage power supplies, this receiver handles high-power configurations up to 1080W total output without requiring auxiliary signal amplifiers.

SR-ZG9101EA-5C Manual Download

Key Features

4-in-1 Configurable Modes

Onboard DIP switches toggle the 5 output channels between single color, tunable white (CCT), RGBW, and 5-channel RGB+CCT configurations.

Wide 12V to 48V Range

Supports input voltages from DC 12V up to DC 48V, catering to standard low-voltage installations and long-run 48V LED strip architecture.

High Current Output

Delivers up to 8A per channel at 12V and 24V, 6A per channel at 36V, and 4A per channel at 48V for high-density strip runs.

Zigbee 3.0 Mesh Integration

Pairs directly with universal Zigbee gateways and acts as a router node to extend signals across your smart home mesh network.

TouchLink Direct Pairing

Enables direct connection to up to 30 Zigbee remotes supporting Zigbee Light Link without needing an intermediary gateway hub.

Green Power Switch Support

Binds directly with up to 20 kinetic, battery-free Zigbee Green Power switches for localized wall switch control.

Technical Highlights

Delivers up to 480W at 12V, 960W at 24V, 1080W at 36V, and 960W at 48V maximum connected load.
Compatible with universal Zigbee coordinators, including ecosystems using Zigbee controller and lights platforms.
Enables smooth 0.1% to 100% dimming curves without stepped jumps or visible output anomalies.
Equipped with TouchLink commissioning for swift localized field binding without network reboots.
Compact 170 x 59 x 29 mm terminal enclosure with screw-down wire clamping terminals for secure conductor retention.

Product Specifications

Parameter	Details
Model Number	SR-ZG9101EA-5C
Connection Type	Screw terminals
Control Protocol	Zigbee 3.0
Input Voltage	DC 12V - 48V
Output Type	Constant Voltage (PWM)
Output Channels	5 Channels
Output Current (12V / 24V)	8A per channel (5CH)
Output Current (36V)	6A per channel (5CH)
Output Current (48V)	4A per channel (5CH)
Max Output Power (12V)	480W total
Max Output Power (24V)	960W total
Max Output Power (36V)	1080W total
Max Output Power (48V)	960W total
Supported Lighting Types	RGB+CCT, RGBW, CCT (Tunable White), Single Color
Remote Binding Capacity	Up to 30 Zigbee remotes (TouchLink)
Green Power Binding Capacity	Up to 20 Zigbee Green Power switches
Dimensions (L x W x H)	170 x 59 x 29 mm
IP Rating	IP20 (Indoor use only)

Application Scenarios

Residential Smart Lighting Automation Integrate 24V tunable white or RGBW LED strip fixtures into smart living spaces. The controller links with home automation coordinators alongside standard RF Tuya Zigbee LED dimmers for voice and app control.

Commercial Hospitality and Dining Deploy across restaurants and hotel lobbies requiring dynamic color shifts and synchronized scenes. Use dedicated handheld transmitters or wall stations such as a Zigbee scene panel handy remote for convenient local table and zone adjustments.

Long-Run Architectural Perimeter Lighting Take advantage of 48V constant voltage inputs to eliminate voltage drop along extensive linear coves, delivering continuous, reliable illumination across large public and commercial spaces.

High-Density Retail Display Cases Drive high-density RGB+CCT tape up to 8A per channel at 24V. When planning centralized mechanical rooms, wire the controller downstream of external Zigbee LED drivers or standard industrial power supplies.

Battery-Free Kinetic Switch Control Mount in retrofit locations where pulling wall wiring is impossible. Pair directly with up to 20 Zigbee Green Power kinetic transmitters to achieve wire-free, battery-free wall switching.

How to Wire & Install This Power Supply & Controller

Set the onboard DIP switches to match your LED strip configuration (Single Color, Tunable White, RGBW, or RGB+CCT) before applying power.
Ensure your DC power supply voltage strictly matches the operating voltage of your connected LED strip lights (DC 12V, 24V, 36V, or 48V).
With AC mains power disconnected from your power supply, connect the DC positive (+) and negative (-) leads from the driver to the controller DC input terminals.
Connect the LED strip output conductors to the 5 channel terminals (V+, R, G, B, W, WW/CW) observing strict polarity markings.
Energize the power source and initiate Zigbee network pairing via your coordinator interface, or commission local handheld controls via TouchLink within 10 cm range.
Verify smooth color tuning, dimming gradients, and full off state across all connected channels.

⚠ Precautions

This unit requires an external DC 12-48V power supply; do not connect AC mains power directly to the terminal blocks.
Verify that total LED load wattage remains within 80% of both the external power supply and the controller channel ratings.
Never adjust DIP switches while the device is powered; always disconnect input power before changing operating modes.
Indoor IP20 enclosure rating: do not expose to moisture, condensation, or outdoor elements without a secondary sealed enclosure.
Maintain adequate spacing around the housing to allow natural convective airflow and heat dissipation under heavy loads.
Ensure all screw terminals are torqued down firmly to prevent loose wire contacts and excessive localized resistance heating.

What's in the Box

✓1 x Sunricher SR-ZG9101EA-5C 5-Channel Zigbee 3.0 LED Controller
✓1 x User Wiring and Commissioning Manual

Frequently Asked Questions

Q: Can this unit convert 120V or 230V AC household current directly?

A:No. The SR-ZG9101EA-5C is a constant voltage DC receiver requiring an external DC 12V to 48V power source matched to your LED strip voltage.

Q: How do I select between RGB+CCT, RGBW, tunable white, and single color modes?

A:The operating mode is configured via physical DIP switches located on the controller body. You must power off the unit before repositioning the switches.

Q: What is the maximum wattage this controller can handle at 24V DC?

A:At 24V DC, the unit handles up to 8A per channel across 5 channels, allowing a maximum combined continuous load of 960W.

Q: Can I operate this controller without an active Zigbee gateway hub?

A:Yes. You can directly pair up to 30 Zigbee remotes using TouchLink commissioning, or pair up to 20 Zigbee Green Power kinetic switches without a gateway.

Q: Does this controller support 48V LED strip lights?

A:Yes. It supports DC 12-48V input, delivering up to 4A per channel at 48V DC for a total output capacity of 960W.

Q: Is this controller rated for outdoor installations?

A:The unit carries an IP20 rating designed for dry indoor locations. For outdoor lighting, mount the controller inside an appropriately sealed, weather-rated enclosure.

DIM CCT RGBW RGBCCT 4-in-1 Zigbee LED Controller SR-ZG9101EA-5C