Spec Sheet - FSLCOB-IC-RGBCCT-840W10

Select Connector:	3 Pin JST Connector (Base), Waterproof Wires, Quick Waterproof Connectors
Select IC Pixels:	28 Pixels/Meter (RGB IC + CCT IC) (Base)
Select Kit:	LED Strips + RF Remote Kit + Power, LED Strips + Panel Control Set + Power, LED Strip Only (Base)
Select LED Quantity:	840 Chips/m (Base)
Select Length:	16.4ft (5 meters) (Base)
Select PCB Width:	10mm (0.39in) (Base)
Select Waterproof Rating:	Non-Waterproof IP20 - Adhesive Back (Base), Underwater IP68 - Adhesive Back, Outdoor Silicone Tube IP67 - Adhesive Back
Availability	In Stock
Condition	Brand New

This DC24V addressable RGBCCT COB LED strip combines continuous diffusion coating with digital pixel control, operating at 23W/m with 840 LEDs per meter. Driven by dual JD36703A integrated circuits per cut unit, the LED strip delivers dot-free linear light across 16 million colors alongside dedicated tunable white from 2700K to 6500K. The 10mm wide flexible circuit board has a 3.1mm profile and handles 140 individually addressable zones across each 5-meter reel. With a single-line SPI data sequence configured in Red, Green, Blue, Warm White, and Cool White (RGBWC), this LED strip coordinates with an addressable RGBCCT controller for dynamic architectural effects.

Key Features

Dual JD36703A IC Architecture

Uses two JD36703A chips per segment to process single-wire SPI control for 5 distinct color channels (RGBWC).

High Density Dotless Illumination

Contains 840 LEDs per meter beneath continuous silicone phosphor to eliminate visible diode spots on reflective surfaces.

RGB Plus Tunable CCT Spectrum

Combines full-gamut RGB diodes with dual phosphor white channels adjustable from 2700K warm white to 6500K cool white.

Precise 71.42mm Cut Intervals

Segmented every 71.42mm with dedicated solder pads to yield 140 controllable zones across a standard 5m reel.

Standard 3-Pin JST Terminations

Equipped with 3-pin JST-SM connectors on both ends for 24V power and single-wire data transmission. Waterproof connectors are optional.

Multiple Ingress Protection Options

Available in IP20 non-waterproof, IP67 silicone tube, or IP68 solid silicone injection for indoor and wet locations.

Technical Highlights

Unique dual-chip architecture pairs two JD36703A ICs to manage 5 output channels, operating with standard SPI controllers compatible with WS2811 protocols.
RGBWC data sequence (Red, Green, Blue, Warm White, Cool White) delivers accurate color channel mapping without firmware color inversion issues.
Operates at DC 24V, reducing current draw to 0.96A/m (23W/m) to limit voltage drop across 5-meter runs.
Total reel power load is 115W, engineered to pair directly with a DC 24V Mean Well power supply such as the LRS-150-24.

Product Specifications

Parameter	Details
Product Model (SKU)	FSLCOB-IC-RGBCCT-840W10
Operating Voltage	DC 24V
Power Consumption	23W/m (115W per 5m reel)
LED Type	COB (Chip on Board)
LED Density	840 LEDs/m
Integrated Circuit (IC)	JD36703A (2 ICs per segment)
Control Protocol	Single-wire SPI (compatible with WS2811/WS2812 RGBCCT data formats)
Color Spectrum	RGB + Tunable White (2700K - 6500K)
Channel Sequence	RGBWC (Red, Green, Blue, Warm White, Cool White)
Pixel Count	140 pixels per 5m reel (28 pixels/m)
Cut Interval	71.42mm (2.81 in)
PCB Width	10mm (0.39 in)
Strip Height / Thickness	3.1mm (0.12 in)
Reel Length	5m (16.4ft)
Ingress Protection Options	IP20 (Indoor), IP67 (Silicone Sleeve), IP68 (Full Silicone)
Standard Connectors	3-pin JST-SM (Red: V+, Green: DAT, White: GND)
Mounting Method	Self-adhesive backing
Operating Temperature	-20°C to +50°C (-4°F to 122°F)
Thermal Requirement	Requires aluminum channel or metal substrate for heat sinking

Application Scenarios

Full-Spectrum Architectural Accent LightingInstall this addressable RGBCCT COB LED strip in ceiling coves and wall grazes to switch between circadian tunable white tasks and multi-zone chasing color palettes.

Commercial Hospitality and Club InstallationsUtilize 140 individually controlled zones across 5 meters to run smooth chase patterns along bar counters, lounges, and stage perimeters using an addressable SPI control system.

Retail Display and Exhibition ShowcaseMount the strip inside an LED aluminum profile above display shelves to render jewelry and apparel under neutral white light during store hours, transitioning to dynamic RGB chases for promotional events.

How to Install & Use This LED Strip

Inspect the LED strip and connect the 3-pin JST-SM plug to an SP530E multi-protocol controller and a 24V power supply to test all color channels and data flow before installation.
Measure the required run and cut the LED strip only along the marked copper solder lines spaced every 71.42mm.
Join cut segments using solder or dedicated 3-pin addressable connectors, verifying correct polarity: Red to +24V, Green to DAT, and White to GND.
Connect the data input tail (indicated by the directional arrows on the PCB) to your controller output and feed 24V power directly to prevent operational errors.

⚠ Precautions

Always adhere this 23W/m LED strip to an aluminum channel; operating it unmounted or rolled on the plastic spool causes heat buildup and accelerates lumen depreciation.
Ensure the controller SPI settings match the RGBWC channel order; incorrect IC channel mapping in the software will swap warm white, cool white, or color channels.

What's in the Box

✓1 × 5m Reel of 24V Addressable RGBWC COB LED Strip
✓1 × 5m Reel of 24V Addressable RGBWC COB LED Strip + SP530E Controller + RB4 RF Remote + LRS-150-24 + AC Plug (if you select the "LED Strips + RF Remote Kit + Power")
✓1 × 5m Reel of 24V Addressable RGBWC COB LED Strip + SP530E Controller + RC4 Panel Remote + LRS-150-24 + AC Plug (if you select the "LED Strips + Panel Control Set + Power")

DC24V Digital LED RGBWC Addressable RGB Tunable White COB Lighting Strip