Related Products
Tick the accessories you need and add them in one go
£31.10
£41.72£45.518% off
£44.00
£13.64
£19.71£22.7613% off
£2.66£3.7930% off
£0.75
Product Information
The WS2815 12V individually addressable 3535 RGB LED strip delivers 96 pixels per meter on an ultra-narrow 8mm flexible printed circuit board. Engineered with integrated WS2815 driver ICs and dual-signal data routing, this LED strip provides unbroken continuous transmission so that a single failed LED does not interrupt the remaining run.
Running on a constant 12V DC input, the 5m reel maintains consistent color saturation and luminance from end to end without visible voltage drop across any solid color. The compact SMD 3535 footprint makes it suitable for concealed linear lighting, slim extrusion channels, architectural reveals, and interactive digital signage projects requiring precise pixel mapping.
Key Features
Individual Pixel Control
Each SMD 3535 RGB LED contains an integrated WS2815 IC, allowing independent 24-bit color addressing for every single node along the LED strip.
Dual Data Breakpoint Resume
Dual-line data transmission ensures that if any single pixel encounters damage, subsequent pixels continue to receive signals normally without system blackout.
Native 12V DC Power Architecture
Operates directly on 12V DC power without inter-pixel dropping resistors, eliminating visible voltage drop over a complete 5m reel run on any display color.
Slim 8mm Flexible Circuit
The narrow 8mm PCB fits into slim aluminum channels and pairs directly with an 8mm silicone neon diffuser for spotless linear diffusion in confined spaces.
Single-LED Cut Capability
Every single LED can be cut individually at designated cut lines every 10.4mm, providing exact dimension matching for custom architectural fixtures.
Factory JST-SM Connectors
Pre-soldered 4-pin JST-SM connectors on both input and output ends allow rapid connection to digital controllers and secondary power injection leads.
Technical Highlights
- 96 individually addressable pixels per meter deliver tight 10.4mm pitch spacing to minimize pixelation in direct-view and diffused accent installations.
- Integrated dual-signal routing includes Data (DI/DO) and Backup Data (BI/BO) lines for fault-tolerant pixel array installations.
- Standard RGB color line sequence integrates smoothly with standard SPI pixel controllers, Madrix software, and digital light consoles.
Product Specifications
| Parameter | Details |
|---|---|
| Product Model | WS2815-3535RGB-96W8 |
| Input Voltage | 12V DC |
| LED Density | 96 LEDs/meter (480 LEDs per 5m reel) |
| Pixel Density | 96 individually addressable pixels/meter |
| LED Package | SMD 3535 RGB |
| Driver IC | WS2815 (embedded inside LED package) |
| Signal Transmission | Dual data lines (Data + Backup Data with breakpoint resume) |
| Power Consumption | 10W/meter (50W per 5m reel at full white) |
| Current Draw | 0.83A/meter (4.17A per 5m reel at 12V DC) |
| PCB Width | 8mm (0.31 in) |
| Reel Length | 5 meters (16.4 feet) |
| Cut Interval | Every 1 LED (10.4mm / 0.41 in) |
| Color Sequence | RGB (standard SPI configuration) |
| Grayscale Levels | 256 levels per channel (16.7 million colors) |
| Ingress Protection | IP20 non-waterproof / IP67 silicone tube waterproof |
| Connector Type | 4-pin JST-SM connectors (12V, DI/DO, BI/BO, GND) on both ends |
| Beam Angle | 120 degrees |
Application Scenarios
How to Install & Use This LED Strip
- Select an appropriate constant-voltage regulated 12V DC power supply delivering at least 60W per 5m reel to maintain a 20% operating safety headroom.
- Check signal direction indicated by directional arrows on the flexible circuit; ensure data flows away from your controller output toward DO.
- Connect the 4-pin JST-SM female connector to your SPI controller, verifying that 12V DC positive, Data (DI), Backup Data (BI), and Ground (GND) correspond correctly.
- Conduct a temporary power-on test across full red, green, blue, and white sequences before peeling the adhesive backing.
- Peel the backing tape progressively, pressing the LED strip firmly onto the mounting substrate using steady finger pressure for 30 seconds per section.
What's in the Box
- ✓1 × 5-meter (16.4ft) WS2815 12V 3535 RGB LED Strip (96 LEDs/m) on plastic reel
- ✓1 × Pre-attached 4-pin JST-SM female connector with separate power injection wire tails
- ✓1 × Pre-attached 4-pin JST-SM male connector
Frequently Asked Questions
Q: What is the advantage of WS2815 over 5V WS2812B strips?
A: The WS2815 operates natively on 12V DC, eliminating visible end-to-end voltage drop across a full 5m reel, while its dual-data line prevents a single damaged pixel from halting downstream signals.
Q: What power supply is required for a 5-meter run?
A: A 5-meter reel consumes 50W at full brightness, so a 12V DC power supply rated at 60W or higher is recommended to maintain the standard 20% power headroom.
Reviews
Customer Experience
Your feedback is important to us! Share your thoughts and photos with other customers.
Downloads
Files for WS2815-3535RGB-96W8Images
These images were taken with Canon EOS 5D Mark IV and the studio light source is provided by Ra 98's full spectrum LED strip to realistically reproduce the colors of the item itself. All copyrights are created by the superlightingled team, please feel free to browse and download if you are a registered user!
LED Strip Light Guide
Common questions about this type of product, answered against this model’s own options. For full figures see the specification above or the spec sheet for this model.
