RF RGBW CC Controller

2 products

The SkyDance RF RGBW CC Controller Series is specifically designed for constant-current (CC) RGBW LED fixtures. Connect these CC controllers to your compatible constant-current RGBW LED lights to independently manage red, green, blue, and white LED outputs through wireless lighting control.

Featuring DC 12V, 24V, 36V, and 48V power input options, these controllers offer four-channel PWM constant-current output with 150mA-500mA and 350mA-1200mA current range. With 4096-level PWM dimming, you can achieve smooth brightness adjustment and precise RGBW color mixing for your connected LED fixtures.

Each RGBW CC controller features a built-in 2.4GHz RF wireless receiver, allowing you to pair it with compatible SkyDance RF RGBW handheld remotes or in-wall panel RGBW remotes. This provides convenient wireless operation of your connected RGBW fixtures, including color selection, brightness adjustment, dynamic lighting effects, and scene control.

Multiple SkyDance RF RGBW CC controllers can synchronize their lighting operation wirelessly within a typical RF control range of up to 30 meters under suitable conditions. One compatible RF remote can operate multiple controllers together or manage separate RGBW CC lighting zones independently. For added convenience, each CC controller supports pairing with up to 10 compatible RF remotes, allowing the same RGBW lighting installation to be operated from different locations.

Frequently Asked Questions About RF RGBW CC Controllers

Direct technical answers from our engineering desk on wiring, power limits, and constant-current drive setups.

An RF RGBW CC controller regulates electrical current directly to each color channel rather than pulsing a fixed output voltage. While a constant-voltage dimmer delivers DC12V or DC24V and relies on resistors on the tape to limit current, an RF RGBW CC controller actively monitors and caps the output current—such as 350mA or 700mA per channel—across Red, Green, Blue, and White. It receives 2.4GHz wireless commands from a handheld remote or wall panel, using 4096-level PWM to dim each color channel smoothly without shifting the forward current curve.

An RF RGBW CC controller will damage standard constant-voltage LED strip lights that use onboard current-limiting resistors. Standard flexible tape requires a fixed DC12V or DC24V supply from an RF RGBW CV controller, where we list 25 models built for parallel resistor strips. CC controllers are engineered strictly for series-wired LED fixtures without internal resistors, such as high-power RGBW architectural wall washers, downlight pucks, and constant-current LED modules that demand a steady milliamp feed.

An RF RGBW CC controller uses four synchronized PWM drive circuits running at 4096 dimming steps to mix colored and white light with laboratory accuracy. Traditional RGB tape blends red, green, and blue diodes to mimic white, which produces an unnatural, low-CRI bluish tint. Adding a dedicated white diode on the fourth channel allows the controller to produce vivid saturated colors, pure architectural white light between 2700K and 6500K, or balanced pastel tones by washing pure white into the color mix.

Every C4-series RF RGBW CC controller includes an external Push Dim terminal that lets you wire a standard normally-open momentary wall switch for manual control without an RF remote. A quick press toggles the fixture on or off, while holding the switch ramps the brightness smoothly between 0% and 100%. If you set the controller to RGBW mode, double-clicking the push switch cycles through 10 built-in color-changing dynamic patterns, retaining the last state in onboard flash memory after power cuts.

Flashing LEDs on an RF RGBW CC controller indicate that the total forward voltage of your LED string exceeds the controller's DC input voltage. For example, if you connect four 9V RGBW multi-chip fixtures in series, the total forward voltage is 36V. Running the controller on a 24V power supply triggers internal undervoltage protection, causing the driver to pulse in an infinite loop. Swapping your power source to a 48V power supply gives the controller the necessary voltage headroom to sustain the series string.

Each RF RGBW CC controller contains an integrated RF transceiver that automatically relays commands to other SkyDance controllers within a 30-meter radius. When you press a button on your 2.4GHz remote, the nearest receiver picks up the radio packet and retransmits it to adjacent units in a daisy-chain mesh. In open air, an array of controllers can stretch over hundreds of meters while keeping dynamic color fades synchronized to within 0.1 milliseconds.

Size your power supply by multiplying the controller's configured channel current by its maximum output voltage, then add a 20% safety margin. If an RF RGBW CC controller runs 4 channels at 700mA (0.7A) on a 48V supply, each channel consumes up to 33.6W (48V × 0.7A), totaling 134.4W with all four channels at 100% white. Adding a 20% headroom factor means you should install at least a 160W, 48V DC power supply to prevent thermal overload on the supply.