Triac CV Dimmable LED Driver

10 products

SkyDance Triac/ELV CV Dimmable LED Drivers are specially designed for low-voltage LED lighting installations in countries and regions with 220–240V mains supply.

With AC200–240V input and DC12V or DC24V constant-voltage output, these drivers receive dimming signals from compatible Triac/ELV wall dimmers or external AC Push-Dim switches to directly power and adjust the brightness of low-voltage LED strips and compatible lighting fixtures.

Available in different power ratings of 40W, 75W, and 150W, each Triac/ELV driver has a maximum load capacity that determines the total LED strip length or number of lighting fixtures it can support.

The connected load must stay within the driver's rated output power, so selecting the appropriate wattage is essential when planning the lighting layout. The actual strip length depends on the power consumption per meter, while the total wattage of all connected fixtures determines the overall load.

A Quick and Deep Understanding of TRIAC Dimmer & Dimming

Triac/ELV CV Dimmable LED Driver Wiring & Load Distribution

Connect the driver's AC200–240V input to the mains supply through a compatible Triac/ELV dimmer. The driver converts the AC mains power into regulated DC12V or DC24V constant-voltage output to directly power the connected LED strips or lighting fixtures.

Connect the LED loads to the corresponding low-voltage output terminals, ensuring that the total connected wattage does not exceed the driver's rated capacity. For multiple LED strips or fixtures, parallel wiring can be used where supported by the driver specifications.

Triac/ELV Dimmer LED Strip Light Driver Wiring Diagram
Push Dim Triac/ELV LED Strip Light Driver Wiring Diagram

When planning the installation, calculate the combined power consumption of all connected loads and consider voltage drop on longer low-voltage cable runs.

FAQ About Triac CV Dimmable LED Driver

Direct answers to common wiring, dimmer compatibility, and sizing questions from our engineering desk.

A Triac CV dimmable LED driver converts AC mains power into a regulated 12V or 24V constant voltage DC output while translating phase-cut dimming signals into smooth pulse-width modulation (PWM). Standard drivers only regulate voltage; a dimmable driver reads the chopped AC sine wave from a wall dimmer and adjusts the low-voltage PWM duty cycle to dim single-colour LED strip lights without changing their colour temperature or rendering index.

Every Triac CV dimmable LED driver in this series supports both leading-edge (forward phase) and trailing-edge (reverse phase or ELV) dimming systems. Trailing-edge electronic dimmers deliver quieter operation and smoother low-end response down to 1%, while traditional forward-phase magnetic dimmers also pair cleanly. If your wall plate has an adjustment dial for minimum brightness, set it slightly above zero to establish a stable firing angle.

Keep the continuous load on a Triac CV dimmable LED driver at or below 80% of its rated nameplate wattage. For example, if you run our 150W 24V dimmable driver, cap your total connected LED strip lights at 120W. That 20% margin prevents the internal switching transistors from overheating inside tight joinery and eliminates random thermal shutdowns during extended evening runs.

Yes, each Triac CV dimmable LED driver equipped with an AC Push-Dim port connects directly to a standard momentary push-button switch. A quick tap (under 0.5 seconds) turns the LED strip lights on or off, while holding the button ramps the brightness up or down smoothly. The driver retains its last brightness level after power loss, so you do not need an expensive rotary dimmer module.

These units require an AC200-240V mains supply and will not output sufficient DC power on a standard 120V circuit. Connecting 120V causes the driver to drop out, buzz, or flash the LED strip lights uncontrollably. If you are operating on North American 120V mains, wire them across a 208V/240V two-pole split-phase circuit or choose our universal input dimming power supplies.

Pick a self-contained Triac CV dimmable driver when you want one compact box converting 230V mains directly into dimmable DC power for your single-colour LED strip lights. If your power supply is already located far away or you need an IP67 waterproof setup driving multiple channels, pair an external non-dimmable power supply with a separate dimming CV controller to separate mains AC conversion from PWM regulation.