Triac Dimming CV Controller

1 products

SkyDance Triac/ELV Dimming CV Controller is a specially designed low-voltage-powered controller for DC12–24V single-color LED strips. This controller receives AC100–240V phase-cut dimming signals from compatible Triac/ELV wall dimmers or smart Triac/ELV dimming modules, or control signals from an external AC Push-Dim switch, and converts them into PWM dimming output for low-voltage LED strips. 

This allows users to control LED brightness through AC-side dimming devices while keeping the LED strips and their DC output circuit operating on the safe low-voltage side with a separate 12–24V constant-voltage power supply.

It is particularly suitable for electricians, lighting designers, contractors, and homeowners who want to use familiar Triac/ELV wall dimmers with DC LED strips. Supporting compatible leading-edge and trailing-edge Triac dimmers, as well as external AC Push-Dim switches, it offers flexible control options for both new installations and retrofit projects.

A Quick and Deep Understanding of TRIAC Dimmer & Dimming

Wiring with a Triac/ELV Dimmer

The SkyDance Triac/ELV Dimming CV Controller supports both two-wire dimmers without a neutral connection and dimmers that require a neutral wire. Connect the AC Triac/ELV dimmer according to the corresponding wiring diagram, matching its neutral-wire configuration.

On the low-voltage side, connect an external DC12–24V constant-voltage power supply to the controller's power input, then connect the single-color LED strip to its PWM output terminals.

Triac/ELV Dimmer Control LED Strip Lights Wiring Diagram

It is an ideal solution for residential lighting renovations, architectural accent lighting, under-cabinet lighting, cove lighting, and other projects where existing Triac/ELV wall dimmers need to be retained while adding or upgrading low-voltage LED strip lighting.

Wiring with an External AC Push-Dim Switch

An external momentary AC Push-Dim switch can be connected to the controller's dedicated AC Push Switch input terminals for wired manual ON/OFF and brightness control. Connect the switch to the designated Push-Dim terminals according to the wiring diagram, while the DC12–24V power supply and single-color LED strip remain connected to the controller's low-voltage input and output terminals.

Push Dim Low-Voltage LED Strip Lights Wiring Diagram

A short press turns the light ON or OFF, while a long press adjusts brightness smoothly. The Triac/ELV dimmer and external Push-Dim switch can also be connected simultaneously, providing two independent control methods for the same LED lighting system.

FAQ About Triac Dimming CV Controller

Direct answers to technical, wiring, and compatibility questions about low-voltage constant voltage Triac dimming controllers from our bench engineers.

A Triac dimming CV controller translates an incoming AC phase-cut dimming signal into a smooth low-voltage PWM output for constant-voltage LED strip lights. Instead of passing high-voltage AC directly to the fixture, this unit connects between a separate 12V to 24V DC power source and your 1-channel LED strip lights. When you adjust an upstream wall dimmer, the controller samples the AC 100V to 240V chopped waveform, reads the firing angle, and converts that ratio into a logarithmic pulse-width modulation output running at 500 Hz.

A Triac dimming CV controller does not convert AC mains line voltage into low-voltage DC power by itself. An all-in-one driver takes AC 110V or 230V mains and steps it down directly to DC. In contrast, this controller is a dedicated secondary-side dimming receiver: it requires an external constant-voltage DC power supply on its DC input terminals, while receiving only the phase-cut control signal on its AC signal terminals. This architecture isolates the dimming control circuit from the primary DC transformer.

At 12V DC, a 15A Triac dimming CV controller delivers up to 180W of continuous load, while at 24V DC it supports up to 360W of single-color LED strip lights. To keep the internal MOSFETs cool and prevent premature thermal throttling, we recommend running no more than 80% of that maximum continuous capacity (144W at 12V and 288W at 24V). If your LED strip lights pull more than 15A, you must divide the run across multiple units or feed downstream runs with an expansion repeater.

This Triac dimming CV controller accepts AC phase-cut signals from standard forward-phase (leading edge / TRIAC) and reverse-phase (trailing edge / ELV) wall units, including Lutron Diva, Skylark, and Leviton SureSlide models. It also pairs directly with our ac triac panel dimmers when you prefer a clean glass rotary or touch wall plate. The controller detects the incoming wave slice between AC 40V and 220V without requiring an auxiliary neutral connection at the signal sensing terminal.

The Triac dimming CV controller includes active thermal shutdown, short-circuit recovery, overload throttling, and input reverse-polarity protection. If the internal heat sink hits 85°C, the controller decreases output duty cycle automatically until safe operating temperatures return. If an accidental short occurs across the output screw terminals, the unit cuts output current immediately, resetting once the short is removed without blowing internal fuses or damaging your upstream DC power supply.