AC Triac Panel Dimmer

5 products

SkyDance AC Triac Panel Dimmers are wall-mounted AC phase-cut lighting controllers designed to directly regulate the power supplied to compatible AC 100–240V dimmable lighting fixtures, LED drivers, traditional incandescent lamps, and high-voltage halogen lighting.

Installed between the AC mains supply and the connected lighting load, these panel-mount wall dimmers control brightness by adjusting the AC waveform through leading-edge (forward-phase) or trailing-edge (reverse-phase) dimming, eliminating the need for a separate low-voltage analog dimming signal line.

Multiple Wall Control Options: Unlike conventional Triac ELV rotary dimmers, SkyDance AC Phase Panel Dimmer offers a variety of wall-mounted control interfaces, including traditional rotary knobs, modern touch-sensitive glass panels, and intelligent Wi-Fi or Zigbee smart dimming panels. Selected models also incorporate 2.4GHz RF wireless technology, allowing additional control through compatible handheld remotes and wireless wall panel remotes.

Whether you are designing a modern residential lighting system, upgrading existing wall dimmers, or integrating traditional AC lighting into a smart home environment, SkyDance AC Triac Panel Dimmers provide a convenient combination of direct AC phase-cut control, intuitive wall operation, and intelligent wireless lighting management.

A Quick and Deep Understanding of TRIAC Dimmer & Dimming

AC Triac ELV Wall Panel Dimmer Wiring & Installation

SkyDance AC Triac/ELV Panel Dimmers are installed directly into an AC 100–240V lighting circuit, providing both local wall control and, depending on the model, additional wireless or smart home control.

Although RF, Wi-Fi, and Zigbee versions use different wireless communication technologies, their basic electrical wiring follows the same principle: connect the AC mains supply to the dimmer's input terminals and connect the controlled lighting load to its AC output terminals.

There are two common installation configurations:

Direct AC Dimmable Lighting

AC 100–240V Mains → SkyDance AC Triac/ELV Panel Dimmer → Compatible AC Phase-Cut Dimmable LED Lamps

This configuration is suitable for compatible AC-powered dimmable LED lamps, incandescent lamps, and high-voltage halogen lighting.

Low-Voltage LED Strip Lighting

AC 100–240V Mains → SkyDance AC Triac/ELV Panel Dimmer → Triac-Dimmable AC-to-DC CV LED Driver → DC 12V / 24V LED Strip

AC 100–240V Mains → SkyDance AC Triac/ELV Panel Dimmer → Triac-Dimmable AC-to-DC CC LED Driver → Constant Current LED Lights

Do not connect ordinary non-dimmable LED drivers or DC 12V / 24V LED strips directly to an AC Triac dimmer.

RF Remote Control Wiring

SkyDance KS, S1-K, and S1-T wall panel AC Triac/ELV dimmers feature built-in 2.4GHz RF wireless receivers in addition to their local rotary or touch controls.

RF Remote Control AC Triac/ELV Lighting Wiring Diagram

After completing the wiring, users can pair compatible SkyDance RF handheld dimming remotes or RF wall panel remotes with the wall panel.

Once paired, the Triac/ELV lighting can be adjusted locally through the wall panel or wirelessly through the matched RF remote. Depending on the selected remote, single-zone or multi-zone control is available.

Wi-Fi Tuya Smart App Setup Wiring

SkyDance TS-K(WT) is a Wi-Fi-enabled rotary AC Triac/ELV panel dimmer that combines traditional wall knob operation with smartphone-based smart lighting control.

WiFi Smart Control AC Triac/ELV Lighting System Wiring

After electrical installation, connect the panel to a compatible 2.4GHz Wi-Fi router and add the device through the Tuya Smart or Smart Life App.

Through the smartphone app, users can:

  • - Turn Triac/ELV lighting ON or OFF and adjust brightness.
  • - Create lighting scenes and preset brightness levels.
  • - Set automatic lighting schedules and timers.
  • - Control compatible lighting through Amazon Alexa and Google Assistant.

Zigbee Smart Home Gateway Integration Wiring

SkyDance TS-K(WZ) is designed for Zigbee-based smart lighting installations, combining a rotary AC Triac/ELV wall dimmer with Zigbee 3.0 wireless communication.

For smart home operation, pair the panel dimmer with a compatible Tuya Zigbee gateway. Once connected, the device can be controlled through the Tuya Smart or Smart Life App, including brightness adjustment, ON/OFF operation, lighting scenes, and scheduled automation. The TS-K(WZ) also supports integration with the Philips Hue App through a compatible Philips Hue Bridge.

Zigbee Remote AC Triac/ELV Lighting System Wiring

Important: A compatible Zigbee gateway is required for network-based remote control and supported voice assistant functions. The Triac/ELV panel's local rotary dimming operation does not require an internet connection.

Important Installation, Load Compatibility & Safety Considerations

Before installing any SkyDance AC Triac/ELV panel dimmer, verify the connected lighting load, electrical ratings, and phase-cut compatibility.

Use only phase-cut dimmable LED lamps and LED drivers explicitly designed for leading-edge or trailing-edge dimming. Ordinary non-dimmable LED drivers may flicker, produce noise, or become damaged.

Choose leading-edge (forward-phase) or trailing-edge (reverse-phase) operation according to the LED driver's specifications. The corresponding DIP switch must be set before energizing the dimmer.

Check the dimmer's rated output current, power capacity, and permissible load for the actual AC supply voltage. When connecting multiple LED drivers, calculate the total load using each driver's rated AC input power and consider its startup inrush current. Do not calculate the maximum driver quantity using the driver's DC output wattage.

Disconnect the upstream circuit breaker and verify that the circuit is de-energized before installation or maintenance. These products operate directly from AC mains and should be installed by a qualified electrician in accordance with local electrical codes.

FAQ About AC Triac Panel Dimmers

Direct engineering answers on installing, wiring, and pairing SkyDance wall-mount phase-cut AC dimming panels.

An AC Triac panel dimmer is a mains-voltage phase-cut wall controller built into an 86x86 mm glass faceplate that mounts directly into a standard single-gang electrical back box. Unlike inline modules hidden inside ceilings, an AC Triac panel dimmer gives you rotary knob or capacitive touch control right on the wall while regulating 100-240V AC output. Across our Triac AC Dimming Series shelf of 59 live models, this category contains our 5 dedicated in-wall panel units designed specifically for finished architectural spaces.

An AC Triac panel dimmer cannot be wired directly to low-voltage DC LED strip lights, but it controls them smoothly when wired ahead of a phase-cut driver. The wall panel regulates the 120V or 230V AC input, which feeds into triac dimmable power supplies that convert the chopped AC wave into smooth pulse-width modulation for your 12V or 24V tape. If you connect mains phase-cut output directly to low-voltage DC strips, you will instantly burn out the LEDs.

Rotary knob triac dimmers give tactile feedback and instant single-turn response from 0% to 100%, whereas touch glass panels rely on a smooth slider strip or stepped tap points. Our rotary units like the S1-K provide 256 dimming levels, click-to-toggle on/off switching, and double-click minimum brightness programming. Capacitive touch models like the S1-T offer an ultra-flat, wipe-clean tempered glass faceplate that matches contemporary architectural switchgear, but rotary knobs remain easier to operate without looking at the wall.

Yes, every AC Triac panel dimmer in this category requires a dedicated neutral wire inside the wall box. Because the glass touch electronics, rotary encoders, and 2.4GHz RF wireless modules require constant low-power standby current, the panel cannot steal power through the load like obsolete two-wire incandescent switches. If your back box only contains a live loop and a switched live with no neutral conductor, you must pull a neutral wire before installing these units.

You select leading-edge or trailing-edge phase-cut mode using the hardware dip switch located on the back housing of the AC Triac panel dimmer before mounting it into the wall box. Setting the dip switch to leading-edge configures forward-phase control for traditional inductive loads and older triac dimmable bulbs, while trailing-edge mode uses reverse-phase MOSFET switching for electronic low-voltage transformers and modern driver electronics. Always disconnect mains power before changing dip switch positions.

Our TS-K(WT) AC Triac panel dimmer integrates directly with 2.4GHz WiFi networks to enable app control through Smart Life and Tuya without an extra hardware hub. We added this model in 2026 to bring native voice control via Alexa and Google Assistant alongside physical rotary dimming. You can set automated schedules, adjust dimming curves, and assign countdown timers from your smartphone while maintaining mechanical dial control for guests on the wall.

An AC Triac panel dimmer is an all-in-one user interface and power controller mounted in a wall box, whereas our ac triac dimmers are compact modules hidden behind push switches or in ceiling junction boxes. Panel dimmers eliminate the need for third-party wall switches and external push-button wiring. However, if your electrical box lacks physical depth or neutral wiring, an inline hidden dimmer paired with a separate battery-powered kinetic wall switch is the cleaner choice.