0-10V DALI Series

24 products

BinColor LED dimming series products include 0-10V/1-10V dimmer/driver and DALI driver. 0-10V/1-10V driver is compatible with 0-10V/1-10V dimming signals, which can dim and change the color of singe-color/color temperature/RGB/RGBW LED lights through 0-10V/1-10V dimmer. 

DALI dimming drivers are compatible with DALI dimming protocols to digitally dim single-color/color temperature/RGB/RGBW LED lights through DALI controllers. Some DALI dimming drivers come with operation buttons and on-screen setting displays for easy operation.

Things You Need To Know About 0-10V Dimmer & Dimming

Frequently Asked Questions About 0-10V & DALI Series

Direct engineering answers on wiring distances, protocol conversion, load capacities, and troubleshooting 0-10V and DALI LED control hardware.

When comparing dali vs 0-10v, the fundamental split is digital addressing versus analog voltage control. A 0-10V circuit controls every luminaire wired to the control pair as one fixed zone by varying DC voltage between 0V and 10V. DALI (IEC 62386) assigns a digital address to each driver on a two-wire bus, letting you group, reconfigure, and dim up to 64 individual drivers without pulling new cables. Read our DALI dimming guide to see how digital bus topology simplifies complex architectural layouts.

You can combine dali and 0-10v lighting controls on one project by placing a protocol bridge between the digital bus and analog runs. Our DC12V-24V converters translate incoming DALI commands into 0-10V analog or PWM signals, allowing central DALI building panels to control standard 0-10V LED dimmers. While contractors often search for an active 0-10v to dali converter, pairing DALI signal converters directly to analog drivers achieves clean bidirectional integration across legacy and digital zones.

Choosing between a 0-10V and 1-10V LED dimmer comes down to whether your control gear needs to switch off completely through the signal wires. A true 0-10V LED dimmer drops output to 0V to turn the LED strip lights fully dark, while a 1-10V dimmer bottoms out at 1V (roughly 10% light level) and requires a separate mains relay to cut AC power. In our category, 12 of our 24 models support 0/1-10V dual operation, letting you set the curve via DIP switch.

Using an architectural 0-10v to dali converter is uncommon because DALI requires an active bus power supply and bi-directional command packets, so jobsites usually convert DALI down to 0-10V instead. When you need to bridge an analog wall slider into a digital run, you feed the analog voltage into a converter that broadcasts broadcast-level DALI packets across the local loop. For projects modernizing older commercial fit-outs, we stock dedicated dimming signal converters that resolve protocol handshakes cleanly.

The BC-331-16A 0-10V dimming driver handles up to 16A on a single channel, which equals 192W on a 12V rail and 384W on a 24V rail. Most standard 0-10V decoders in this footprint cap output at 5A or 10A, requiring secondary power repeaters for runs over 15 meters. If you need a high-capacity single-channel unit with push-dim terminal support, the BC-331-16A push dimmer replaces older DIN rail versions without needing external signal boosters.

To run multi-channel LED strip lights over DALI, use a DT6 multi-channel DALI dimming driver such as the BC-343-LED for tunable white or BC-344-LED for RGBW tape. Each channel occupies one sequential DALI short address on your bus (for example, addresses 0, 1, 2, and 3 for red, green, blue, and white), letting the DALI master command colour mixing digitally. This eliminates the multi-conductor home-runs that analog 0-10V setups require for separate colour channels.

You can install a dali 1-10v or 0-10V dimming driver in wet locations by choosing an IP67-sealed unit like the BC-331-WP waterproof 1-10V dimmer. While standard indoor drivers carry IP20 enclosures with screw terminals, our waterproof model uses silicone potting and water-tight cable glands rated for -30°C to +55°C operation. It operates on DC12V-24V and accepts standard 1-10V analog signals, letting you run exterior landscape tape or architectural facade lighting directly from your indoor controls.