Triac CC Dimmable LED Driver
12 productsSkyDance Triac/ELV CC Dimmable LED Drivers are designed for constant-current LED lighting installations in countries and regions with AC200–240V mains supply. Unlike constant-voltage Triac/ELV drivers that provide fixed 12V or 24V output for LED strip lights, these drivers deliver regulated constant-current output to LED modules, COB LED light sources, and other compatible constant-current lighting fixtures.
With AC200–240V or AC220–240V input, DC10–52V output range, and current ratings from 100mA to 1050mA, they provide direct power and brightness control through compatible Triac/ELV dimmers or external AC Push-Dim switches.
Available in different output power ratings from 12W to 40W, these drivers are suitable for a variety of LED fixtures with different forward-voltage and current requirements.
The rated output current must match the LED fixture's requirements, while the total forward voltage of the connected LED load must remain within the driver's output voltage range. The driver's maximum power capacity also determines the compatible LED load and should be considered when selecting a suitable model.
TF-30A 30W 150-900mA Triac Dimmer Driver for LED Lights
TF-40A 40W 300 to 1050mA Dimmable Constant Current LED Driver
10W Triac Dimmable LED Driver: Multi-Current & Configurable
12W Triac Dimmable LED Driver | Constant Current 350mA
36W Triac Dimmable LED Driver | Multi-Current SwitchDim
9W Triac Dimmable LED Driver - Constant Current Output
FAQ About Triac CC Dimmable LED Driver
Engineering answers for selecting, wiring, and troubleshooting constant current Triac dimmable drivers on mains circuits.
A Triac CC dimmable LED driver converts incoming AC line voltage into a regulated constant current output—such as 350mA or 700mA—while reading phase-cut signals from standard wall dimmers. Unlike constant voltage units that fix the DC voltage rail, a constant current driver continuously adjusts its DC voltage (for example, across a 10V to 52V window) to keep the current steady through bare LED emitters, downlights, and spotlights. Our category features 12 live models delivering 9W to 50W, designed specifically for fixtures that lack internal current-limiting resistors.
No, our catalog models in this series are engineered strictly for 200–240VAC mains input at 50/60Hz. Running a 200–240VAC rated Triac CC dimmable LED driver on a standard 120V circuit causes severe operational faults: the driver will either fail to boot, strobe rapidly, or shut down as its internal PFC circuit drops below the minimum operating threshold. If your project is located in North America on standard 120VAC line voltage, you need a dedicated 100–277VAC universal driver rather than these 200–240V units.
Set the multi-position DIP switch on the driver casing before connecting AC line power. Always verify the current rating on your LED fixture's label first: setting a 350mA COB downlight to 700mA will permanently degrade or blow the emitter, while setting a lower current simply reduces maximum lumen output safely.
Yes, our Triac CC dimmable LED driver models are compatible with both leading-edge (forward-phase Triac) and trailing-edge (reverse-phase ELV) dimmers. While traditional Triac dimmers cut the front of the AC sine wave, electronic low-voltage (ELV) trailing-edge switches cut the falling tail, which generally produces quieter operation and smoother low-end dimming down to 1%. You can also pair them with an AC Triac panel dimmer or a secondary momentary push switch on supported switchDim terminals.
Not directly on the driver itself, but you can achieve wireless RF dimming by placing an RF-enabled Triac dimmer module upstream on the 230V mains feed. In that setup, your wireless handheld remote or wall panel communicates via 2.4GHz RF to an RF AC Triac dimmer, which phase-chops the incoming AC mains fed into this constant current driver. The driver then reads that sliced AC sine wave and adjusts the LED light output cleanly without needing any secondary control cabling running into the ceiling void.