Related Products
Tick the accessories you need and add them in one go
€20.29
€59.14
€7.05
€22.94€26.4913% off
€31.77
€2.64
€4.41
Product Information
The FSLRGB-SM16703AP-96W8 is a DC 12V addressable RGB LED strip engineered on an ultra-narrow 8mm flexible PCB with 96 SMD3535 LEDs per meter. Featuring an external SM16703AP dual-signal control IC for every 3 LEDs, this digital LED strip provides continuous signal transmission, preventing downstream data interruption if an individual IC encounters a failure. Each 5-meter reel consumes 12W to 14W per meter and comes pre-fitted with 4-pin JST signal connectors and 2-pin auxiliary power injection leads at both ends. For stable dynamic chases and multi-pixel scenes, pair this tape with a compatible addressable RGB controller and dual-ended DC injection.
Key Features
Dual Data Breakpoint Resume
External SM16703AP ICs utilize main and backup data lines so a single damaged IC does not break signal flow to subsequent pixels.
Narrow 8mm PCB Profile
Slim 8mm width and 2.1mm height allow direct mounting inside narrow aluminum extrusions or an 8mm silicone neon diffuser for spotless linear output.
96 LEDs per Meter Density
Equipped with 96 SMD3535 RGB diodes and 32 addressable ICs per meter, delivering a tight 31.25mm cutting segment for accurate architectural fitting.
Dual-End Factory Connectors
Supplied with 4-pin JST SM data terminals and independent 2-pin DC power leads on both reel ends to simplify dual-ended power injection.
RBG Color Sequence Calibration
Configured with an RBG channel order that integrates directly into digital SPI controller setups without color inversion errors.
Product Specifications
| Parameter | Details |
|---|---|
| Product Model (SKU) | FSLRGB-SM16703AP-96W8 |
| Operating Voltage | DC 12V |
| Power Consumption | 12W - 14W per meter (60W - 70W per 5m reel) |
| PCB Width | 8mm (0.31 in) |
| Strip Height | 2.1mm |
| Standard Reel Length | 5 meters (16.4 ft) |
| LED Type | SMD3535 RGB |
| LED Density | 96 LEDs/m (480 LEDs per reel) |
| Control IC | SM16703AP External IC (Dual Data) |
| IC Quantity | 32 ICs/m (160 ICs per reel) |
| Pixel Resolution | 32 pixels/m (1 pixel per 3 LEDs) |
| Cut Interval | 31.25mm (1.23 in) |
| Color Sequence | RBG |
| Ingress Protection | IP20, IP67 |
| Termination | 4-pin JST connector and 2-pin power wires on both ends |
| Mounting Method | Self-adhesive backing tape |
| Operating Temperature | -20 deg C to +45 deg C |
Application Scenarios
How to Install & Use This LED Strip
- Measure the run and cut strictly across marked copper solder pads at 31.25mm intervals if custom lengths are required.
- Connect the 4-pin JST signal interface to your controller and mate the positive and negative leads to a regulated 12V UL-listed power supply.
- Carry out a complete operational test across red, green, blue, and white scenes prior to removing the adhesive liner.
- To make secure angle transitions or jumpers, solder lead wires directly onto exposed solder pads or use compatible 3-pin addressable LED strip parts.
⚠ Precautions
- 12V Single-End Power Drop Notice: While individual red, green, and blue diodes show minimal drop on single-ended power, blended colors (such as mixed white, yellow, or purple) experience visible voltage drop across the second half of a 5m reel. Connecting DC 12V power at both ends of each 5m reel is required for uniform color accuracy.
- Verify your controller output mode matches the RBG color sequence of this SM16703AP strip to prevent swapped red and blue channels;.
- Ensure power supply wattage includes at least 20% electrical headroom above total strip load (minimum 84W rated driver per 5m reel).
What's in the Box
- ✓1 x 5-meter (16.4ft) reel of 12V SM16703AP 96 LEDs/m 8mm addressable RGB LED strip
- ✓Factory-soldered 4-pin JST connector and 2-pin DC power injection wires on both ends
Frequently Asked Questions
Q: can you cut rgb led strip lights
A: Yes, this LED strip can be cut every 31.25mm along designated copper solder pads, where each group of 3 LEDs forms one independently controlled pixel.
Q: how to control rgb led strip
A: This strip requires an SPI digital pixel controller compatible with SM16703, UCS1903, or WS2811 protocols set to the RBG color sequence.
Q: Why is dual-ended power injection recommended for this 5m reel?
A: When powered from one end only, mixed colors show voltage drop and color shifting along the latter half of the 5m run; supplying 12V to both ends ensures consistent color and brightness across all 96 LEDs per meter.
Reviews
Customer Experience
Your feedback is important to us! Share your thoughts and photos with other customers.
Downloads
Files for FSLRGB-SM16703AP-96W8Images
These images were taken with Canon EOS 5D Mark IV and the studio light source is provided by Ra 98's full spectrum LED strip to realistically reproduce the colors of the item itself. All copyrights are created by the superlightingled team, please feel free to browse and download if you are a registered user!
LED Strip Light Guide
Common questions about this type of product, answered against this model’s own options. For full figures see the specification above or the spec sheet for this model.
