Narrowest 3mm SK6812 RGB Individually Addressable 5V LED Strip 3.28ft - Black PCB

Features: 

1. There are 60 Addressable RGB LEDs per meter,  and 3mm wide for 60LEDs/meter, DC5V input, and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set the color of each LED's red, green and blue component with 8-bit PWM precision (so 24-bit color per pixel).

2. Super narrow design, you can customize any shape according to the project requirements, usually, it is applied to LED luminous word illumination or special complex model backlight programming lighting

3. The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip.

4. Only 1 digital output pin is required to send data down.

5. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for you.

6. The SK6812 is very similar to the WS2812B, and it can be used as a drop-in replacement in most applications because it features the same interface and color order (so LED strips based on the SK6812 and WS2812B can be chained together). The main difference between the two drivers is that the SK6812 has voltage-independent color and brightness over a wide voltage range, which means that the colors of the LEDs should not be affected by a drop in the supply voltage as much as they are on the WS2812B.

SK6812 Chips Specifications Download     

Light strips advantages

   With plasticity, can be free to bend the shape — fixed in the uneven surface, easy to install (using the 3M self-adhesive) and other advantages;

   With waterproof, in case of high temperature and low temperature does not change color, low voltage long life, and other advantages;

   With bright colors and soft light (1LED lights can be composed of a loop — every 1 light can be cut to use), energy saving and environmental protection and other advantages are the ideal replacement of neon products (than the neon energy saving 70%), It is decorative contours. Making a variety of modeling the ideal lighting.

Standards and Certifications

Specifications

Input voltage:   DC5V

Power:   9.8watt/meter

LED Chip Model:   SMD2020

LED resource:   SK6812 LED

IC Type:   SK6812 IC (1 IC drives 1 led chip)

Q'ty of LED:    60leds/Meter Available

Q'ty of IC:   60 pixel /Meter

Cuttable:   every LED is cuttable

Dimensions:     L100cm(39.37 in ) x W0.3cm(0.12 in ) x H0.25cm(0.1 in )

PCB color:   BLACK Available

Protection rate:   Non-waterproof  or IP67 waterproof (sealed in silicone tube) 

Colors:   Full color RGB, dream color changing; 

Grey scale:   256

Bits/color:   8-bits/color;total 24bit for RGB color

LED wavelengths:   630nm/530nm/475nm

Average Life (hrs):   50000Hours+

Certification:   CE,FCC,GS,SAA,RoHS,CCC

Similar to WS2812B LED strip, the SK2812 led strip has 3 wires for sending data - one V+ pin, one GND pin, and one data pin. That means you need 3 pins to control strip. Because the data is separated, you can use any processor speed or type to control these strips. an addressable RGB LED strip is a long flexible strand of LEDs each of which can be individually set to a certain color (hence: addressable). By varying the level of red, green and blue (RGB) per LED many color combinations can be made you can use any processor speed or type to control these strips, you can use any microcontroller or microprocessor, including Arduino, Raspberry Pi, BeagleBone, Propeller, SparkCore, and any 'raw' microcontrollers/microprocessors to control the strip. 

This strip comes as a single full meter with a 3-pin JST SM connector on each end. Every LEDs segment can be cut. Solder to the 0.1" copper pads and you're good to go.you can also connect strips together to make them longer. To power this strip, you need a 5V power supply.  

 You can cut the strip every few inches,                      The back of the strip is fitted with a strong                    IP67/IP68 type which will come with 

allowing you to freely design your project                    3M tape, allowing you to peel and stick lights                 mounting brackets

without worrying about space requirements

to many different surfaces.