Related Products
Tick the accessories you need and add them in one go- €44.13
- €22.94€26.4913% off
- €39.72
- €16.77€23.8330% off
- €14.11
- €36.19
- €33.54€57.3842% off
Product Information
The DC12V UCS2904B addressable RGBW 5050 SMD LED strip light delivers independent color chasing, scene programming, and true architectural white illumination across a 16.4ft (5-meter) reel. Operating at DC 12V, this digital led smd 5050 strip integrates external UCS2904B constant-current driver ICs, configuring every 3 LEDs as one independently controllable pixel (20 pixels per meter, 100 pixels per reel).
Each SMD 5050 package integrates four semiconductor dies—red, green, blue, and a dedicated white emitter (selectable in 3000K warm white, 4000K natural white, or 6000K daylight white)—eliminating the uneven bluish casts common to standard RGB-only mixing. Built on a 10mm wide flexible printed circuit board (FPC) with 18W per meter power consumption, this smd led strip light includes pre-soldered 3-pin signal and 2-pin power-injection JST-SM connectors on both ends for clean installation and robust data continuity.
Key Performance Features
External UCS2904B IC Control
Each external UCS2904B driver IC controls 3 SMD 5050 RGBW LEDs with 17mA constant-current accuracy within +/-1.5% between channels, providing 256 grayscale levels per channel and an 800 kbps transmission rate.
4-in-1 SMD 5050 RGBW Architecture
Houses dedicated red, green, blue, and pure white diodes within a single 5.0mm x 5.0mm package, delivering true functional white illumination alongside saturated dynamic chasing effects.
50mm Segment Trimming
Features designated cut marks spaced every 3 LEDs (50mm / 1.97 in), allowing field customization and solder-pad splicing to match precise architectural alcoves and cabinet runs.
Dual JST-SM Connector Design
Equipped with factory-installed 3-pin data connectors and auxiliary 2-pin power injection leads on both reel ends, simplifying bilateral power injection to prevent end-of-run voltage drop.
Four Environmental Protection Ratings
Available in non-waterproof IP20 (2.1mm profile height), surface glued IP65, outdoor silicone sleeved IP67, and fully submersible IP68 configurations with mounting brackets or adhesive backing.
Product Specifications
| Parameter | Details |
|---|---|
| Product Model | UCS2904B-RGBW-60W10-12V |
| Input Voltage | DC 12V |
| Power Consumption | 18W/m (90W per 5m roll) |
| IC Type | External UCS2904B (SOP8) |
| LED Type | SMD 5050 4-in-1 RGBW |
| LED Density | 60 LEDs/m (300 LEDs per 5m roll) |
| Pixel Resolution | 20 pixels/m (100 pixels per 5m roll; 3 LEDs/pixel) |
| Cut Interval | Every 50mm (2.0 in) / 3 LEDs |
| White Color Options | 3000K Warm White / 4000K Natural White / 6000K Daylight White |
| Grayscale Level | 256 levels (8-bit per channel, 32-bit color depth) |
| PWM Scan Frequency | 1.8 kHz |
| Data Protocol | Single-line Return-to-Zero (NZR) 800 kbps |
| PCB Width | 10mm (0.39 in) |
| Profile Height | 2.1mm (IP20 bare board) |
| PCB Color | White |
| Reel Length | 16.4ft (5.0 meters) |
| Terminal Connectors | 3-pin JST-SM (V+, Data, GND) + 2-pin JST-SM (V+, GND) |
| Waterproof Options | IP20, IP65, IP67, IP68 |
| Manufacturer Warranty | 2 Years |
Application Scenarios
How to Install & Use This LED Strip
- Check that the incoming DC power supply matches DC 12V. Disconnect all AC mains power before making any wire terminations.
- Trim the LED strip only along the marked copper cut lines spaced every 50mm (3 LEDs). Never cut across active IC circuits or internal traces.
- Connect the 3-pin input JST-SM plug to your SPI pixel controller: Red wire to DC12V (V+), Green wire to Data (DAT), and White wire to Ground (GND). Ensure the data direction matches the printed directional arrows on the PCB.
- Connect both the front and rear 2-pin power wires to your 12V DC power bus. Dual-end power injection is strongly advised on 5-meter runs to maintain consistent color balance when all RGBW channels operate simultaneously.
- Configure your controller software (such as WLED, Madrix, or standard SPI hardware) to the UCS2904 or UCS2904B IC profile, selecting the RGBW color order that matches your unit.
- Never connect this DC 12V LED strip directly to AC 110V/220V mains or DC 24V power sources, as overvoltage will instantly damage the UCS2904B ICs and LED chips.
- Single-end power injection across a full 5-meter reel will cause slight voltage drop at the far end when displaying full-white or mixed multi-color scenes; always inject DC 12V power at both ends for uniform brightness.
- Select an appropriate power supply rated for at least 110W per 5-meter reel (18W/m x 5m = 90W, plus a 20% operating headroom buffer).
What's in the Box
- ✓1 x 16.4ft (5m) Reel of DC12V UCS2904B RGBW 60 LEDs/m LED Strip Light
- ✓Pre-soldered 3-Pin JST-SM Signal Connector and 2-Pin Power Injection Leads on Both Ends
⇩ Downloads & Documents
Frequently Asked Questions
Q: What type of controller do I need for this LED strip?
A:You need a dedicated addressable LED controller that is specifically compatible with the UCS2904 or UCS2904B RGBW single-line data protocol, capable of sending 800 kbps non-return-to-zero SPI signals across four color channels.
Q: Can I connect multiple 5-meter rolls together?
A:Yes, you can connect the data line from one roll to the next. However, you must inject power from a separate LED power supply for each 5-meter roll to avoid brightness and color issues caused by voltage drop.
Q: Why is dual-end power feeding recommended for this 12V strip?
A:At 18W per meter, a full 5-meter reel consumes 90W under full load. Feeding DC 12V power only from one end causes minor resistance-based voltage drops at the tail end during mixed-color operation; injecting power at both ends ensures uniform illumination and color consistency.
Reviews
Customer Experience
Your feedback is important to us! Share your thoughts and photos with other customers.
Downloads
Files for UCS2904B-RGBW-60W10-12VImages
These images were taken with Canon EOS 5D Mark IV and the studio light source is provided by Ra 98's full spectrum LED strip to realistically reproduce the colors of the item itself. All copyrights are created by the superlightingled team, please feel free to browse and download if you are a registered user!




LED Strip Light Guide
Common questions about this type of product, answered against this model’s own options. For full figures see the specification above or the spec sheet for this model.


















