Related Products
Tick the accessories you need and add them in one go
$89.98
$39.98$45.9813% off
$58.98$64.989% off
$64.98
$199.00
$9.98
$206.50
Product Information
This 24VDC DMX addressable RGBW LED strip uses the TM512BC integrated circuit to decode native DMX512 differential signals directly without requiring an intermediary SPI decoder. Built on a 12mm white flexible PCB with 72 SMD5050 4-in-1 LEDs per meter, each TM512BC IC independently drives a segment of 6 LEDs across 4 distinct color channels (Red, Green, Blue, and White).
Operating at 15W per meter on a 24V DC circuit, this 10-meter continuous reel delivers smooth DMX chasing RGBW animation sequences while reducing current draw and voltage drop over long linear installations. Explore our full line of rgbw dmx led strip solutions for more types.
Key Features
Native DMX512 Protocol Integration
Onboard TM512BC driver chips connect directly to standard DMX512 consoles and controllers without external SPI signal translators.
High-Density 72 LEDs/m Layout
72 SMD5050 RGBW quad-die LEDs per meter mounted on a 12mm white PCB deliver uniform color mixing and 15W per meter power distribution.
24V DC Low-Voltage Architecture
24V operation allows full 10-meter single-feed runs with minimal voltage drop compared to 5V or 12V addressable tapes.
Granular 83.33mm Pixel Control
Cuttable every 83.33mm (6 LEDs per segment) to match custom architectural lengths and achieve 12 individual controllable pixels per meter.
Industrial 5-Pin Connectivity
Equipped with 5-pin JST-SM connectors for power and DMX data lines, with optional IP67 waterproof screw-lock connectors available.
Technical Highlights
- Direct RS485 differential bus compatibility (D+, D-, and address write line) eliminates signal jitter across extended cable runs.
- Each 10-meter reel consumes 150W total at full output, requiring a dedicated 24V DC power supply sized at 180W or higher to maintain 20% operating headroom.
- Integrates directly with any led artnet dmx controller for multi-universe pixel mapping in Madrix, Resolume, or Obsidian Onyx.
- The 12mm PCB width fits inside a 12mm silicone neon diffuser for dot-free architectural line-of-light installations.
- Compatible with 5pin rgbw led strip parts including solderless jumper cables, extension leads, and injection tees.
- Independent white channel allows clean pastel tones and true architectural white illumination alongside dynamic RGB color chases.
Product Specifications
| Parameter | Details |
|---|---|
| Product Model (SKU) | DMXRGBW-TM512-5050X72 |
| Operating Voltage | 24V DC |
| Power Consumption | 15W per meter (150W per 10m reel) |
| LED Density | 72 LEDs per meter (720 LEDs per 10m reel) |
| LED Chip Type | SMD5050 4-in-1 RGBW |
| Driver IC | TM512BC (Standard DMX512 protocol) |
| Pixel Resolution | 12 pixels per meter (6 LEDs per pixel) |
| DMX Channels | 48 DMX channels per meter (4 channels per pixel) |
| Reel Length | 10 meters (32.8 feet) |
| PCB Width | 12mm (0.47 inches) |
| PCB Color | White |
| Cut Interval | 83.33mm (3.28 inches, 6 LEDs) |
| Beam Angle | 120 degrees |
| Ingress Protection | IP20 (Indoor dry) or IP67 (Silicone tube) |
| Standard Connector | 5-pin JST-SM (PI, A/D+, B/D-, GND, 24V+) |
| Optional Connector | 5-pin waterproof connector / wire |
Application Scenarios
How to Install & Use This LED Strip
- Connect the 5-pin input lead to your DMX signal source: wire 24V+ and GND to the power supply, and connect D+ (A) and D- (B) differential data lines to your DMX controller output.
- Use a DMX address programmer to write starting DMX addresses to the TM512BC chips prior to final mounting, or address sequentially from pixel 1.
⚠ Precautions
- Do not exceed a 10-meter continuous run on a single power feed; inject 24V DC power at both ends if connecting runs longer than 10 meters to prevent voltage drop.
What's in the Box
- ✓1 × 10m (32.8ft) Reel 24V DMX Addressable RGBW LED Strip
- ✓1 × 5-Pin JST-SM Female Connector (Pre-soldered on input end)
- ✓1 × 5-Pin JST-SM Male Connector (Pre-soldered on output end)
Frequently Asked Questions
Q: how to program TM512BC addressable DMX RGBW led strip？
A: Set the starting DMX address using a handheld TM512 programmer, patch 4 DMX channels per pixel in your lighting software (such as Madrix or QLC+), and build chasing or color-fade cues mapped to the strip's 12 pixels per meter.
Q: how to control DMX512 addressable led strip？
A: You can control this TM512BC LED strip using any standard DMX512 lighting desk, Art-Net/sACN Ethernet node, or standalone programmable DMX SD-card controller outputting standard RS485 differential signals.
Q: Can this TM512BC LED strip be cut to length?
A: Yes, this LED strip can be cut every 83.33mm (every 6 LEDs) at the clearly marked cut lines on the 12mm PCB.
Reviews
Customer Experience
Your feedback is important to us! Share your thoughts and photos with other customers.
Downloads
Files for DMXRGBW-TM512-5050X72Images
These images were taken with Canon EOS 5D Mark IV and the studio light source is provided by Ra 98's full spectrum LED strip to realistically reproduce the colors of the item itself. All copyrights are created by the superlightingled team, please feel free to browse and download if you are a registered user!
LED Strip Light Guide
Common questions about this type of product, answered against this model’s own options. For full figures see the specification above or the spec sheet for this model.
