Long RGBW 24V LED Tape 12mm 60-LEDs/m Strip Lights 5m 10m 15m

Model: FSLCCRGBW-24V-5050X60 Review stars 0.0 (0 Reviews) Various options in stock
Starting at: $32.98
Qty Discounts Off Price
1-20
$32.98
21-50
$31.99
51-99
$31.00
100+
$29.68
* Discounts may vary based on options below
Select Specifications:
Select PCB Thickness:
Qty: -+
❓ Ask a question about this item — an engineer replies within 12 hours
Free shipping over $299Ships via DHL / UPSWarranty covered

Accept the project customization, please contact us for commercial offers and technical support.

  • Product Information
  • Reviews
  • Downloads
  • Images
  • LED Strip Light Guide

Product Information

This long RGBW 24V LED tape uses onboard constant current ICs to deliver uniform illumination across continuous runs up to 15 meters (49.2ft) from a single 24V DC power feed with no visible voltage drop or color shift. Engineered with 60 SMD5050 4-in-1 chips per meter on a 12mm 2oz copper PCB, each meter consumes 15W while providing full color mixing and dedicated white output. 

Designed for continuous perimeter accents, large architectural coves, and exterior facades, this LED strip avoids intermediate power injection points. Connect with an external RF RGB+CCT control system and pair with an indoor 24V Mean Well power supply or an outdoor-rated unit to maintain steady output across large installations.

Key Features

Constant Current Regulation

Onboard IC drivers maintain identical milliamp delivery to every diode across 15 meters without end-to-end brightness loss.

SMD5050 4-in-1 Diodes

Integrates red, green, blue, and true white diodes inside a single LED package for uniform color blending without multi-color shadowing.

15-Meter Single-Feed Run

Powers an entire 15m reel from one end, eliminating complex mid-circuit power feeds and messy parallel cabling.

2oz Pure Copper PCB

Features a 12mm wide flexible circuit board with double-thickness copper traces for reduced resistance and efficient thermal spread.

Dual-Ended 5-Wire Pigtails

Comes pre-wired with 5-conductor bare wire leads on both reel ends for streamlined electrical connection.

Four IP Protection Grades

Available in IP20 non-waterproof, IP65 spray-coated, IP67 hollow silicone tube, and IP68 solid silicone potting.

Technical Highlights

  • Single-feed 15-meter run capability: Standard 24V LED strip lights show noticeable color shifting and lumen attenuation beyond 5 to 10 meters. Integrated constant current driver ICs regulate the operating current per cut segment, eliminating human-visible voltage drop from 0m to 15m.
  • 2oz flexible copper circuitry: Double-layer 2-ounce electrolytic copper prevents overheating, limits circuit resistance, and increases structural durability when handling long linear installations.
  • Precision white integration: Dedicated white emitter allows true neutral or warm white architectural illumination alongside saturated multi-color dynamic scenes.

Product Specifications

ParameterDetails
Model SKUFSLCCRGBW-24V-5050X60
Working VoltageDC 24V
Circuit ArchitectureConstant Current IC Regulation
Power Consumption15W per meter (4.57W per foot)
LED TypeSMD5050 4-in-1 RGBW
LED Density60 LEDs per meter (18 LEDs per foot)
Reel Length Options5 meters (16.4ft), 10 meters (32.8ft), 15 meters (49.2ft)
Maximum Run Length15 meters (single end feed)
PCB Width12mm (0.47 in)
PCB Copper Thickness2oz flexible double-sided copper
PCB ColorWhite
Ingress Protection OptionsIP20 / IP65 / IP67 / IP68
Cut Interval100mm (3.94 in) / 6 LEDs per cut section
Connection Type5-conductor bare wire pigtails on both ends
Beam Angle120 degrees
Color Rendering Index (White)CRI ≥ 90
Operating Temperature-20°C to +50°C (-4°F to 122°F)

Application Scenarios

Long-Run Architectural Cove LightingIdeal for seamless ceiling perimeter coves in hotel lobbies, conference spaces, and open-plan residences. Deploying this long led lighting setup eliminates visible color drop at the far end of the room without running secondary power cables back to the driver.
Commercial Building Exterior FacadesUtilize the IP67 silicone tube or IP68 solid encapsulated LED strip powered by a 24V waterproof power supply along building outlines, rooflines, and outdoor canopies for uniform RGBW accent washes.
Theatrical and Entertainment Venue PerimetersInstall continuous long led light strips along auditorium walls, stage edges, and entertainment suites where consistent RGB color mixing is critical across extended viewing distances.

How to Install & Use This LED Strip

  1. Unroll the LED strip from the spool and connect the 5-conductor leads (+24V Black, R Red, G Green, B Blue, W White) to your controller to test full-color operation before final adherence.
  2. Measure the designated run length. If cutting is necessary, cut only along the marked copper solder lines spaced every 100mm.
  3. Peel back the adhesive liner gradually and press the LED strip firmly along the mounting surface, applying steady pressure for at least 30 seconds per section.
  4. Connect the 24V DC output terminals of your power supply to the RGBW controller, ensuring correct polarity and driver capacity.

⚠ Precautions

  • Do not power this LED strip while coiled on the plastic reel for longer than 30 seconds; heat buildup will damage the PCB and components.
  • Mounting inside an aluminum channel is required for 15W/m power loads to ensure sufficient heat dissipation.
  • Always calculate power requirements with a minimum 20% safety margin when selecting a DC 24V power supply.

Power Consumption Reference

Based on 15W/meter rated consumption with a 20% driver overhead margin (Total Watts × 1.2). Select the next standard DC 24V driver capacity.
LengthPowerDriver
5 meters (16.4ft)75W24V 100W driver (e.g., LRS-100-24 or XLG-100-24)
10 meters (32.8ft)150W24V 200W driver (e.g., LRS-200-24 or XLG-200-24)
15 meters (49.2ft)225W24V 300W to 320W driver (e.g., LRS-350-24 or XLG-320-24)

What's in the Box

  • ✓1 × Selected Length Reel of 24V Constant Current RGBW LED Strip
  • ✓Pre-attached 5-conductor bare wire pigtails on both ends of the reel

Frequently Asked Questions

Q: How does rgbw led strip light work?

A: An RGBW LED strip incorporates four individual color dies (Red, Green, Blue, and White) inside each SMD5050 package. By controlling the voltage level on each color channel, you can produce millions of mixed colors or run pure white illumination independently.

Q: How long can you run an rgbw 12v led strip vs this 24v constant current LED strip?

A: A standard 12V RGBW LED strip typically suffers visible voltage drop beyond 5 meters. This 24V LED strip uses constant current ICs to support uninterrupted single-feed runs up to 15 meters with zero lumen decay.

 

Reviews

Customer Experience

Your feedback is important to us! Share your thoughts and photos with other customers.

Downloads

Files for FSLCCRGBW-24V-5050X60
Need CAD drawings, IES files or a signed test report? Contact our engineers and quote the model number.

Images

These images were taken with Canon EOS 5D Mark IV and the studio light source is provided by Ra 98's full spectrum LED strip to realistically reproduce the colors of the item itself. All copyrights are created by the superlightingled team, please feel free to browse and download if you are a registered user!

 Long RGBW 24V LED Tape 12mm 60-LEDs/m Strip Lights 5m 10m 15m Long RGBW 24V LED Tape 12mm 60-LEDs/m Strip Lights 5m 10m 15m Long RGBW 24V LED Tape 12mm 60-LEDs/m Strip Lights 5m 10m 15m

LED Strip Light Guide

Common questions about this type of product, answered against this model’s own options. For full figures see the specification above or the spec sheet for this model.

Which controller does it need?
Colour-changing LED strip lights need a controller with one output per colour channel — for this model that is a 5-pin RGBW controller at the same voltage. Choosing a controller
Which waterproof rating should I choose?
Available on this model: Underwater IP68 - With Brackets · Underwater IP68 - Adhesive Back · Outdoor Silicone Tube IP67 - Adhesive Back · Outdoor Silicone Tube IP67 - With Brackets · Surface Glued IP65 - Adhesive Back · Non-Waterproof IP20 - Adhesive Back. IP20 is for dry indoor use, IP65 handles splashes, IP67 suits outdoor and wet areas, IP68 is for continuous submersion. Choosing a waterproof rating
Can I cut it to length?
Yes. Cut only on the marked cut lines between the copper pads — the cut interval for this model is on its spec sheet. Rejoin with solder or a solderless connector. Cutting LED strip lights · we can also cut to length and fit your connector before shipping: custom LED strip light assembly.
What size power supply do I need?
Take the watts per metre from the specification above, multiply by the length you are running, then add about 25% headroom. Power calculation guide · Choosing a power supply
Complete your setup
Picked for this model from items in stock.